Question about 1992 Geo Tracker

Open Question

Remove door panel from 1990 geo tracker - 1992 Geo Tracker

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: HOW DO YOU REMOVE THE RADIO FROM A 1995 GEO TRACKER????????

To remove the radio:
Remove the ashtray by raising the armrest cover and removing the two screws at the rear of the ashtray. Slide the ashtray back and then lift it out. Be careful of the two front tabs, as you don't want to break them.
Reach below the wood console, where the ashtray front tabs were inserted. Loosen and remove the two wing nuts.
With a small, long flat bladed screwdriver, pry out the leather shifter surround. The leather shifter surround has a center chrome retaining ring, the leather surround, and then finally a black plastic surround. The chrome retaining ring has 3-4 tabs which are locked in below the leather surround. It depends on the year of the Jaguar. Probably the 95 has three, but maybe four. They should be at the front and rear of the trim piece (2 front and 1 back, or 2 front and two back) but I've seen then on the sides. The point is, you have to be careful with the screwdriver and find the tabs. The screwdriver should be slid between the leather and the retainer. Pull upwards on the retainer gently, and as you loosen the tabs, it will come out.
Remove the leather surround. Once the chrome retainer has been removed, it should be easy to work it out of the console.
Loosen the black trim ring gently as it has tabs as well, but they are visible once the leather trim has been removed. Lift it upwards out of the wood trim and pull it to the side out of the way. You don't need to disconnect the wires, just lay the black trim to the side.
Lift the rear of the wood console trim and gently, gently slide it back and up. It will try to hang on the leather console, and can be difficult. Patience is important, as the walnut on the ski slope cracks easy (really easy).
Once the wood console trim (ski slope) is removed, you should have a row of screws up the side of the center control panel, where the radio and AC controls are. There are four to six on each side, depending on what Jaguar used at the time, as the 95 cars mechanically are somewhat of a blend of the XJ40 and the XJ300. Remove these screws, and note any spacers that were behind them. These spacers get lost quickly, and cause the ski slope to sit awkwardly on the console.
The radio will slide forwards once these screws are removed. Remove the radio harness and the antenna lead. As the books say, assembly is reverse of removal.
Good luck, and let me know if you have questions. If you are replacing the radio, let me know as I have the harness wiring codes and can help you with that as well.

Posted on Jul 01, 2008

  • 14036 Answers

SOURCE: 94 & 95 Geo Tracker obd1 cable

you need the same brand cable.

Posted on Apr 06, 2009

  • 2 Answers

SOURCE: reset check engine light on 1995 geo tracker

I had the very same problem with my 94 tracker and it turned out to be something simple. My check engine light had popped on after it had hit 100,000. I went through all of the suggestions that people had suggested (unplug battery......etc) and still to no avail. Searching the internet, I came across a website called suzukiforum.com and there, this guy was able to help me with my problem. It turned out to be a maintenance switch that kicks on every 50,000 miles. This switch is like a secret that the auto manufactures use to ploy owners of their cars to bring to the dealer and then rack up the dollars in unnecessary "repairs". The switch is located under the dash and can be hidden anywhere. From the assistance of the guy on the forum, he was able to send me photos of this damn switch and possible locations where it may be mounted. I found mine in about 5 minutes, where it was attached to the steering column. It's a tiny switch, that you slide up or down, depending on what position it is in upon finding it. If it's up, then slide it in the down position and visa versa. Once you do this, the check engine light will go off. Make sure you do not have the car running and you can even unhook one of the battery posts, just to make sure you don't hit anything while rooting around under the dash. Good luck!

Posted on Apr 30, 2009

  • 31 Answers

SOURCE: Am Replacing Timing Belt On 1990 GEO Tracker 4x4

most of the time there will be one mark on the crank pulley gear and the one on the cam pulley gear.usually a dot or a straight line.

Posted on Apr 17, 2010

  • 72 Answers

SOURCE: 1995 4x4 geo tracker front wheel bearings

first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to locate the fuel pump fuse on a 1990 geo tracker 1.6


seems you asked this 3 times now., old posts.
there is no dedicated fuse. here. sorry, !
its IG-coil
proof.
http://www.fixkick.com/INJECTORS/89/89-90schem1.jpg

not only that, but the ECU software does not run the pump for 3seonds, key on ,like all 1991+ sidekicks/trackers, etc.

Jan 31, 2014 | 1996 Geo Tracker 2 Door

1 Answer

Where is the fuel pump fuse on a 1990 geo tracker


old post, this car is not 1991 and newer that do have a FI fuse.
this generation 1.
it uses 1 fuse for ECU , spark and pump.
called IG-COIL
as seen here
for others, with this car the below is key to whats there. EFI wise.
http://www.fixkick.com/INJECTORS/89/89-90schem1.jpg

Jan 31, 2014 | 1992 Geo Tracker

1 Answer

Where is the ecm located in 1990 geo tracker 1.6l


old posts
same all tracker, vitara in 90s.
behind the left front speaker.
is this clear.?
or others searching i post facts.
http://www.fixkick.com/ECU/ECU.html#Removal_of_ECU:

Jan 31, 2014 | 1990 Geo Tracker

1 Answer

My 1990 Geo Tracker "died"


I have the same problem few days ago, and still didn't find any solution. Can any one please help?????20

Jul 28, 2011 | 1990 Geo Tracker

1 Answer

Can a 1997 1.8 engine be put in a 1990 geo tracker


A machinist can make a adapter plate to marry any transmission couple!! but the rest of the hurdles that u have to jump over to make the transformation is up to u. Are up to the task??

Jul 11, 2010 | 1990 Geo Tracker

1 Answer

1990 geo tracker There is a little button at the base of the


could be a hold button to hold that gear or a overdrive button or traction control. i would drive it up to 55 mph and click the button in if the car revs up or shifts its a overdrive button or traction control. I would leave it unclicked.

Feb 06, 2010 | 1996 Geo Tracker 2 Door

1 Answer

NEED TO CHANGE FUEL PUMP ON A 1992 GEO TRACKER


i dont think you do remove the back seat and right under there should be some screws or bolts with wires connected to the fuel pump removing the bolts should do the job

Nov 14, 2009 | 1997 Geo Tracker 2 Door

1 Answer

1990 geo tracker fusebox.


sick elect.

fuse box above left knee
and in engine bay , right fender top.

you have ratty wiring , clean it up.
or problem will continue.

Mar 06, 2009 | 1990 Geo Tracker

1 Answer

1990 GEO trakcer window regulator


interior door panel is removed...window glass is removed from regulator...regulator (criss cross scissors shaped) with bolts or rivets holding it in place in window frame is removed....motor is removed from regulator if it is power window......reverse procedure with replacement with exception of bolts needing to replace rivets usually when DYI...good luck and hope that gives you a general picture of the job, which is rated at 1.5 hrs in the book for a pro to do

Dec 04, 2008 | 1993 Geo Tracker

2 Answers

My 1990 geo tracker wont start


STARTER RING GEAR, TEETH MISSING?

Oct 07, 2008 | 1990 Geo Tracker

Not finding what you are looking for?
1992 Geo Tracker Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...