Question about Cars & Trucks

Open Question

How to replace the starter on a 2000 Oldsmobile silhouette

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Replacing dashboard lights on an 2000 Oldsmobile Silhouette Van?

the light bulbs are not replacable unless you can solder, you have to replace the complete instrument cluster, get one from a junk yard 100 bucks.

Posted on Sep 25, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: drain the antifreeze on a oldsmobile silhouette

Under the bottom of the radiator on the there is a drain ****, you will have to raise the car and crawl under it to see it, be careful to not break it, the screw in plug is fragile, it will be hard to unscrew.

Posted on Oct 11, 2008

keeperoffire
  • 106 Answers

SOURCE: 2002 Oldsmobile Silhouette ABS Light is on and

The first thing i would check is all 4 abs sensors at the wheels.You can do this with a volt meter set on ac voltage and spin the wheel if it generates voltage at all on the meter its good.

Posted on Mar 06, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

  • 1986 Answers

SOURCE: Replacing mirror on 1998 Oldsmobile Silhouette

you'll need to remove your door panel (screws are by the door handle, arm rest, under door and side of door) and remove the cover adjacent to your mirror to remove the bolts to remove the mirror.

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 Oldsmobile silhuette won't start


How is the starter & solenoid? Tested that?

Battery reads 12.6 volts & you had it tested?

Aug 26, 2014 | 2000 Oldsmobile Silhouette

1 Answer

My starter went out in my 2000 Oldsmobile Silhouette. I replace it with a brand new starter, without key in ignition the starter was winding as soon as I reconnected the battery. However, while doing...


You hooked it up wrong . Is there power at the purple wire all the time ?
ignition the starter was (winding ) ???as soon as I reconnected the battery. The starter cranks the engine !It's really called a cranking motor not starter . Do you know where that comes from ? Before electric starters you cranked the engine by hand . Suggest you take it to a qualified repair shop.

Jun 10, 2017 | 2000 Oldsmobile Silhouette

1 Answer

How do I replace a starter on a 1999 Oldsmobile silhouette.


follow your positive battery wire to the starter .there is two bolts holding it in place 14mm or 15mm socket then loosen the wires from starter

Jul 10, 2011 | 1999 Oldsmobile Silhouette

1 Answer

How to replace thermostate


usually its under the top hose housing

Jul 05, 2010 | 2000 Oldsmobile Silhouette

2 Answers

03 Oldsmobile Silhouette 3.4L Starter stays engaged at times.


Sounds like time for a new starter. While it could be electrical, in that the starter circuit is remaining engaged, more than likely it is mechanical. As the starter wears, you get play in the starter gear. Replacing the starter should take care of it. If you have recently had the starter off or replaced it, it could be misaligned, causing a similar problem.

Mar 27, 2010 | 2003 Oldsmobile Silhouette

2 Answers

Fixing my 2000 Oldsmobile Silhouette Starter


over time our starters get a flat spot on them from wear. Or the solenoid is starting to go out. The solenoid is an electric switch that mounts on the starter. In my opinion its your starter....

Feb 01, 2009 | 2000 Oldsmobile Silhouette

1 Answer

No prower 2000 Oldsmobile Silhouette


Check all battery connections make sure they are tightly secured. Check for broken battery cables, if all are intact. Check battery/Main Fuse. contact if you need more help. Good Luck

Dec 27, 2008 | 2000 Oldsmobile Silhouette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...