Question about 2000 Isuzu Rodeo

1 Answer

I'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

Posted by on

  • yadayada
    yadayada May 11, 2010

    try the public library.

  • Anonymous Mar 26, 2014

    what do the main bearing caps torque to

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Isuzu Master
  • 545 Answers

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Isuzu Rodeo 3.2 v6 torque for rod and main bearings and the other piece


Most autoparts stores have this info available. You will need your vin as well as the Date of manufacture (on the sticker drivers door jamb). This makes sure you get the correct info as sometimes changes are made during a production run.

Jul 17, 2016 | Isuzu Cars & Trucks

2 Answers

I need the specs for the main bearing and connecting rods on a 2000 Nissan Xterra 3.3 v6


Main Bearing Torque 67-74 ft lbs
Rod Bearings Torque 28 - 33 ft lbs

Sep 24, 2015 | 2000 Nissan Xterra

1 Answer

Torque specs for 3.2 1996 conectting rod bolts on isuzu rodeo


rod bolt tension on the 3.2l (6vd1) engine is 55 Nm

May 02, 2014 | 1995 Isuzu Rodeo

1 Answer

Hi,i need torque settings for con rod and oil galley bolts on holden rodeo V6 3.5 ltrs 6VE1


connecting rods 36-45 foot pounds and oil galley 25-35 foot pounds. make sure you dont over tite them under tite, at lease the connecting rods. wish you luck.

Jul 23, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

What is the torque specification on the main and conecting rod bearing of an isuzu npr 4bd2?


Main bearing caps 116-130 ft-lbs
Connecting Rods 58-65 ft-lbs

This is for the 2.2L Diesel engine.

May 04, 2011 | 1995 Isuzu Rodeo

1 Answer

Hello and help, I need the main bearing, big end and flywheel torque settings for an Isuzu 3.1 td 1997, my manual only seems to have v6 petrol engines in it for some reason. many thanks Ron...


I have a 1997 Rodeo with the V6 3.2L engine. The crankshaft main bearing caps are torqued to 29(lb-ft).

The crankshaft pully is torqued to 123 (lb-ft).

Feb 26, 2011 | Isuzu Trooper Cars & Trucks

1 Answer

Torque specs for 1.5 kia rio connecting rod


TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

May 22, 2010 | 2001 Kia Rio

1 Answer

2000 Isuzu Trooper Specs


Tighten the connecting rod cap nuts
Torque : 54 N·m (5.5 Kg·m/40 lb ft)

Jun 30, 2009 | 2000 Isuzu Trooper

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

TORQUE SETTINGS ISUZU RODEO FOUR CYLINDER


I dont know the specific answer for your question, but I own a 1995 Rodeo and there is an online community you could probably check out that Im sure would have the answer for you.

Check out www.planetisuzoo.com, sign up and post your question there. There are several knowledgeable people there and some good information as well.

Jan 03, 2009 | 2001 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

955 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...