Question about 1998 Suzuki Sidekick

1 Answer

Non start,engine turns over,getting spark and fuel pressure,compressions approx 7 bar

Posted by on

  • Anonymous Mar 25, 2014

    Good compression and spark

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 293 Answers

Have your valve timing checked. Place the pulley timing mark on the 0 BTDC mark on the timing cover. Open the distributor cap. The rotor should be pointing to the # 4 terminal of the cap. If not then you may have a timing belt problem. But if the valve timing is okay, try replacing the mass air flow sensor, check the resistance specs of the TP valve, or replace the fast idle valve.

Posted on May 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2000 Jeep Grand Cherokee Laredo 4.7 liter code reads p0307 turn the car off when I turn it back on started misfiring and sputtering and wont stay started now help


code p 0307 is misfiring on no 7 cylinder ====causes --- engine mechanical fault ---wiring---ignition/ fuel system--injector --ECT/MAF sensor---ECM
look for low fuel pressure or ignition control module

May 31, 2016 | 2000 Jeep Grand Cherokee Laredo

2 Answers

1996 geo prizm will turn over but will not start.


CHECK FUSES TO MAKE SURE FUEL PUMP FUSE IS NOT BLOWN. MAKE SURE THAT YOU ARE GETTING GAS FROM THE TANK BY CHECKING THE FUEL LINE AFTER THE FUEL FILTER. SOMETIME THE FUEL FILTER CAN BE CLOGGED UP.

Nov 28, 2014 | Geo Cars & Trucks

2 Answers

Why does the engine turn but wont start on a 2001 chrysler voyager


Hi, it's hard to turn the wheel because the power steering only works when the engine is running.
your non start issue could be several things? So start by checking the basics like petrol,plugs,fuses etc....
also did the car stop when you were driving or after over night?.
Is your car petrol,diesel?

Jul 11, 2014 | 2001 Chrysler Voyager

1 Answer

I have A chevy silverado and it is hard to get it to turn over. when it finally does turn over the truck runs fine.


Engine cranks normally, but it does not fire:
You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---

Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked.

Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).

Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system. Or you can also get the fuel pressure tested at local car garage, If fuel pressure is low then its a fuel pump and fuel filter related problem.

Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------

This troubleshooting will let you know the problem.Thanks.

Mar 01, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Van cranks but will not start


Hi, if the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.

To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. IF it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.

Dec 22, 2010 | 1996 Chrysler Town & Country

2 Answers

My vw will crank but will not start running i


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the Schroeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.


Thank you!!

Jun 30, 2010 | 2001 Volkswagen Passat

1 Answer

Well my car wont start,tryed new battery still doesnt start. trey to pop the clutch didnt start. what could it be?


Hi,
The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..
Thank you !!

Jun 01, 2010 | 1996 Nissan Maxima

1 Answer

My car wont start


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..



Thank you !!

May 30, 2010 | 2002 Cadillac Deville

2 Answers

Car wont start


Hi,
If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..


Thank you !!

May 19, 2010 | 1989 Oldsmobile Delta 88

2 Answers

2001 expedition cranks but wont start


check your crankshaft position sensor

Mar 21, 2010 | 2000 Ford Expedition

Not finding what you are looking for?
1998 Suzuki Sidekick Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...