Question about 1993 Oldsmobile Achieva

1 Answer

Timing marks I Have no info on 93 olds cutlass cerria s 2.5 4cyl. Trying to verify timing. Can you help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Electronic ignitions have none. the marks are made on inner componets for assembly only

Posted on May 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set timing


cam or spark.?
my guess, it's CAM BELT TIME>" right>?
2.3L gas engine. there is also a diesel.
2.3L 4ZD1

why not say the JOB first.????????

ill give the first 16 instructions then photos
  1. Disconnect the negative battery cable.
  2. Loosen and remove the engine accessory drive belts.
  3. Remove the cooling fan assembly and the water pump pulley.
  4. Drain the fluid from the power steering reservoir.
  5. Unbolt and remove the power steering pump. Unbolt the hydraulic line brackets from the upper timing cover and move the pump out of the work area without disconnecting the hydraulic lines.
  6. Disconnect and remove the starter motor if a flywheel holder (part No. J-38674) is to be used.
  7. Remove the upper timing belt cover.
  8. Rotate the crankshaft to set the engine at TDC/compression for the No. 1 cylinder. The arrow mark on camshaft sprocket aligns with mark on the rear timing cover.
  9. Remove the crankshaft pulley.
  10. Remove the lower timing belt cover.
  11. Verify that the engine is set at TDC/compression for the No. 1 cylinder. The notch on the crankshaft sprocket aligns with the pointer on the oil seal retainer.
  12. Release and remove the tensioner spring to release the timing belt's tension.
  13. Remove the timing belt.
  14. Unbolt the tensioner pulley bracket from the engine's front cover.
  15. If necessary, unbolt and remove the camshaft sprockets. Use a puller to remove the crankshaft pulley if necessary. Don't loose the crankshaft sprocket key.
the marks, now.
the 2.3 and 2.6 engines are sisters

so here are the 2 marks.

http://forum.planetisuzoo.com/viewtopic.php?t=41296&highlight=match+mark

easy no?

the car is and Isuzu Faster sold in uSA as "Pickup"
and 18 other names world wide.
so answering for USA PICKUP only.

Feb 16, 2016 | 1993 Isuzu Pickup

1 Answer

3.4 dohc timing


there are timing marks or notches on the head and a timing (dot) on the cam gear, and also on the crank gear and block.make shure these are all allined before tightning the belt tensioners.

Mar 19, 2014 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Looking for timing marks for a 3.1


set the ff:
cranckshaft set the gear straight up = 12 o'clock (#1 piston must be at TDC)
camshaft set the gear straight down = 6 o'clock
to verify, the rotor of the distributor is pointing at #1 plug wire.

Feb 24, 2012 | 1993 Oldsmobile Cutlass Supreme

1 Answer

I am trying to get my 93 plymouth acclaim back in time. the timing belt broke. where does the distrubutor need to be and the the timing marks so it will be in time?


the distributor rotor should be pointed towards the #1 plug wire on the distributor cap.mark on the distributor housing where the rotor is pointing.put the crankshaft so the 0 timing mark on the timing cover is pointing to the slot mark on the crankshaft pulley(harmonic balancer).the cam timing mark will look like an oblong hole with a slot mark(one on each side)of it,the oblong hole should face up and centered on the head surface (not a little of center one way or the other).this is how the marks should be lined up.assuming this is a 4 cylinder motor.

Apr 05, 2011 | 1993 Plymouth Acclaim

1 Answer

Can you tell me where I can print instructions for free to help me change my timing belt in a 93 ford festiva


Here are the instructions for removing the timing cover, and for replacing the timing belt. If this is helpful, please click my accept button! Thanks!
Remove accessory drive belts.
  1. Remove water pump pulley to pump hub attaching bolts, then the pulley.
  2. Remove right inner fender panel to gain access to crankshaft pulley.
  3. Remove outer crankshaft pulley attaching bolts, then the outer stiffener/spacer and outer pulley
  4. Remove inner stiffener/spacer, attaching screws, inner pulley and baffle plate.
  5. Remove attaching bolts, then the upper and lower timing covers.
  6. Reverse procedure to install. When installing crankshaft pulley, ensure curved lip on baffle plate and deep recess of inner pulley face outward

8fb9fc4.gif
  1. Remove timing belt covers as outlined previously.
  2. Remove timing belt tensioner pulley attaching bolt, then the tensioner pulley, spring and spring cover
  3. If reusing old belt, mark direction of rotation on belt to aid installation.
  4. Remove timing belt from crankshaft and camshaft sprockets.
  5. Check crankshaft and camshaft sprockets, tensioner pulley and timing belt for wear or damage. Replace components as necessary.
  6. Align camshaft and crankshaft sprocket timing marks with marks on cylinder head and oil pump housing
  7. Install timing belt. If reusing old belt, ensure belt is installed so that direction of rotation mark made during removal is positioned correctly.
  8. Install spring and spring cover onto tensioner pulley, then install pulley and attaching bolt. Do not tighten bolt at this time.
  9. Install tensioner spring onto anchor, then tighten pulley attaching bolt to torque listed at the end of this section.
  10. Reinstall timing belt covers.

spacer.gif 2006-05-25_081817_fest2.thumb.gif
This photo shows timing marks.


59f76eb.gif

Jul 14, 2010 | 1993 Ford Festiva

1 Answer

Timing marks for 3.4 v6 1995 olds cutlass supreme


It doesn't have any marks. Make your own before you remove the belt. If the belt was broke or you already removed the belt then you will have to remove the valve covers and install specialty tools into the ends of the camshafts to line everything up correctly.

May 17, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Cant find timing marks on camshaft sprockets on 91 olds cutlass supreme 3.4 doh. need diagram to line up marks


THE MARKS SHOULD BE MARKED AT THE OUTTER SURFACE OF THE CAM SPROCKETS THERES 4 TOTAL ON THE CAMS AND TWO ON THE CRANK. GOOD LUCK THIS PICTURE IS RIGHT OUT OF MY TIMING MARK BOOK......bc3b21f.jpg2

Jan 23, 2010 | 1991 Oldsmobile Cutlass Supreme

1 Answer

Timing mark


Go to autozone.com and register for full free online repair manual with everything you should ever need.

Sep 16, 2009 | 1986 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1993 Oldsmobile Achieva Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...