Question about 1996 Honda Odyssey

1 Answer

Throttle Body Problem

Engine surging when accelerate and won't go over 70 MPH. New Fuel pump,MAP sensor,and cleaned out throttle body plus new gasket. What caused this malfunction.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 207 Answers

Check to see if there is a vacuum leak. Make sure the mounting bolts and nuts at the throttle body and intake manifold are tight. Did you replace the PCV valve?

Posted on Jan 03, 2014

Testimonial: "Additionally, I replaced the TPS and having a hard time to the adjust the right voltage for CT and WOT reading. It's completely not adjustable. this could be the Throttle problem itself because the vehicle has over 200 miles."

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: 2003 CR-V Throttle Position Sensor replacement

Try cleaning the IAC (Idle Air Control valve.) by buying spray carb cleaner and removing the air cduct from the engine. On the fuel system side look into the hole and try to locate 2 holes on the side . With the engine running at about 1200 rpms, spray about 10 seconds worth of cleaner at the 2 holes. Turn the engine off. Let the cleaner soak. Then repeat procedure. The IAC can also be removed and cleaned if you wish.

Posted on Feb 16, 2009

  • 3 Answers

SOURCE: 2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low

yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

Posted on May 12, 2009

  • 1149 Answers

SOURCE: 1994 honda civic 1.5 16v stalling after pressing accelerator from idle

Another place to look is your IAC, or Idle air control valve. It is bolted to the back of the intake manifold, and can be removed and cleaned. It is usually the cause of most Honda Idle problems.

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced original engine with another 1.5 used mazda engine. Now i am having problems getting new engine to accelerate on take off (dead stop) and will not go past 60 mph


If you have to many years between the engines, you may need to replace the sensors. Also clean the inside of the throttle body.

Jun 13, 2015 | Mazda Cars & Trucks

1 Answer

2007 trailblazer, rpms fluctuate and pulse at maintained speed


Problem with electronic throttle control maybe. Any light's lit on the instrument cluster or messages engine power reduced . Could be a sign a position sensor is going bad . The gas pedal assembly has to sensors as does the throttle body . You could try cleaning the throttle body bore . Having a qualified repair shop hook up a diagnostic scan tool to view sensor data would be a good thing .
007 Idle Speed Problems Scan Data for Idle
1 reason your cars throttle body needs cleaning Gain lost horsepower and...

Oct 22, 2017 | Cars & Trucks

2 Answers

On a 3.5 engine code reads low idle? any idea


LOW IDLE CAN BE CAUSED BY MANY THINGS.CLOGGED AIR FILTER. LOW COMPRESSION OR MISFIRE CONDITION.IDLE AIR INLET PASSAGE OR THROTTLE BORE IS DIRTY OR FULL OF DEPOSITS.IDLE AIR CONTROL VALVE FAILED.MASS AIR FLOW SENSOR COULD BE OUT OF CALIBRATION. THROTTLE PLATE THROTTLE SHAFT OR LINKAGE IS DAMAGED OR STICKING.PROBABLY HAVE REMOVE THROTTLE BODY ASSEMBLY REMOVE IDLE AIR CONTROL VALVE AND THROTTLE POSITION SENSOR.BUY CAN OF CARBURETOR OR THROTTLE BODY CLEANER SPRAY CLEAN ALL CARBON BUILT UP AROUND THROTTLE PLATES AND BORE.LET AIR DRY BUY A NEW THROTTLE BODY GASKET.

Jul 05, 2010 | Chevrolet Colorado Cars & Trucks

1 Answer

I pass every test for smog except for the emissions (HC) part. The limits are 120 at 15mph and 95 at 25 mph. I'm at 155 and 160. I've replaced the catalytic converter, entire exhaust from tail pipe to...


Has anyone tried adjusting the fuel air mixture?

Based on what I am reading this is a gas engine and I am also assuming it is fuel injected. (Or does it have throttle body fuel injection?)

I suspect a case of dirty fuel injectors at the moment. They will need to be removed and cleaned.

If you have throttle body fuel injection then you will need the fuel air mixture adjusted.

If you respond can you let us know the "engine size" that is installed please. It would help us to help you in troubleshooting.

Thanks for using Fixya. Kelly.

Feb 08, 2010 | 1993 Chevrolet K2500

3 Answers

1991 Toyota Pickup with 293,000 miles on it. I have recently noticed that upon hard acceleration the truck hesitates a bit before acceleration. This does not always occur, bit it seems that it occurs...


Assuming that this is a multi-port fuel injected engine. Is the check engine light on? If so, rent a scanner, read out the code(s), and pursue to repairs. Fuel pressure may be low--plugged fuel filter or worn out fuel pump. Exhaust system may be restricted somewhere. O2 sensor is getting tired. Throttle position sensor is about worn out. Several sensors in the intake system can affect performance, but should show up with the scanner test. Run a can of injector cleaner in the fuel tank

Sep 08, 2009 | 1991 Toyota Pickup

1 Answer

2000 S-type Fail Safe Engine mode is intermittent.


change the throttle body posistion sensor and change the plugs if the throttle body was dirty the plugs can now be fouled out causing the problem the 02 sensor may be clogged as well from the cleaning try thid first this should work if not let me know ill tell you what else you can do hope this solves your problem.

Jul 03, 2009 | 2000 Jaguar S-Type

Not finding what you are looking for?
1996 Honda Odyssey Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...