Question about Cars & Trucks

Open Question

Asd relay location - Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
seanpwright
  • 2030 Answers

SOURCE: Car runs fine for 5 Sec then loses spark thru ASD

The inertia switch is in the rear of the car most times in the trunk area\

Posted on Jul 22, 2010

Ad
mensaman151
  • 377 Answers

SOURCE: 2000 dodge ram 1500 van - fuel pump relay and ASD

write the numbers down on a tablet call your dealer for a new relay

Posted on Oct 24, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of fuel pump shut off switch 99 dodge ram 1500


Dodge does not use a fuel pump cutoff switch, that is Ford and Mazda, and that is is on triggered on impact that exceeds 3 G's. You have what is called and ASD fuel pump shut off relay, it is also triggered in a crash. The ASD is locate in the underhood fuse and relay center. Refer to the owner's manual for location.

Aug 24, 2017 | Dodge Cars & Trucks

1 Answer

2004 dodge ram SLT WHERE IS THE ASD RELAY SENSOR CODE T0688


ASD relay is located in the under hood relay box.

Aug 13, 2015 | Dodge Cars & Trucks

2 Answers

Can you tell me where the asd relay is located


one more Guessyah question, where is... easter egg hunts
if you read the manual its clear. (posted 100s of times here)
or read the door index in the PDC box it lists the ASD there.,
1993 to NOW.
here we go posted 100s of times.
the ASD can drop out for 8 reasons,, scanning the PCM finds that easy. if you dont scan it ,i bet you never find why it drops.
gas engines,(answered)
here is page from chapter 8w-10-7, free to look)
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

now the relay.



25820021-l14j4fdleibzw1xgq2q0eyq3-2-0.jpg
my guess, (hey no symptoms posted, so....)
asd skool
http://www.fixkick.com/Jeeps/ASD.html

there is no need to post complex PDC wiring using words, omg hard....
the link1 above has the full schematic, every inch off it.
read the schematic and see that the PCM controls the ASD !
at all times.
and has been posted here over 100 times, ever search here?
see those?

Aug 13, 2015 | 1996 Jeep Cherokee

1 Answer

Auto shut down fuse blows when I start the truck?


This information is straight out of the 1997 Breeze/Stratus/Cirrus Factory Service Manual (Yes I paid the $90 for it years ago)

__________________________________________________ _______________

Automatic Shutdown (ASD) sense - PCM Input

The ASD sense circuit informs the PCM when the ASD relay energizes. A 12 volt signal at this input indicated to the PCM that the ASD has been activated. This input is used only to sense that the ASD relay is energized.
When energized, the ASD relay supplies battery voltage to the fuel injectors, ignition coils, and the heating element in each oxygen sensor. If the PCM does not receive 12 volts from this input after grounding the ASD reley, it sets a Diagnostic Trouble Code (DTC).

Automatic Shutdown Relay - PCM Output

The PCM operates the Automatic Shutdown (ASD) relay and fuel pump relay through one ground path. The PCM operates them by switching the ground path for the solenoid side of the realys on and off. Both realys turn on and off at the same time.
The ASD relay connects battery voltage to the fuel injectors and ignition coil. The fuel pump relay connects battery voltage to the fuel pump.
A buss bar in the power distribution center (PDC) supplies voltage to the solenoid side and contact side of the relay. The ASD relay power circuit contains a 20 amp fuse between the buss bar in the PDC and teh relay. The fuse also protects the power circuit for the fuel pump relay and pump. The fuse is located in teh PDC.
The PCM controls the relay by switching the ground path for the solenoid side of the relay on and off. The PCM turns the ground path off when the ignition switch is in the Off position. When the ignition switch is in the On or Crank position, the PCM monitors the crankshaft position sensor and the camshaft position sensor signals to determine engine speed and ignition timing (coil dwell). If the PCM does not receive the crankshaft position sensor and camshaft position when the ignition switch is in teh Run position, it will de-energize teh ASD relay.
The ASD relay and fuel pump relay are located in the PDC near the battery. The inside top of the PCD cover has a label showing relay and fuse location.

ASD and Fuel Pump Relays

The following description of operation and tests apply only to the Automatic Shutdown (ASD) and fuel pump relays. The terminals on the bottom of each relay are numbered.

'------------------'
' __85 ___________'
' __87A '87 '30 ___' Sorry for the crudeness of this. This is supposed to
' __86 ___________' be the relay terminals!
'------------------'

OPERATION
- Terminal number 30 is connected to battery voltage. For both the ASD and fuel pump relays, terminal 30 is connected to battery voltage at all times.
- The PCM grounds the coil side of the relay through terminal number 85.
- Terminal number 86 supplies voltage to the coil side of the relay.
- When the PCM de-energizes the ASD and fuel pump relays, terminal number 87A connects to terminal 30. This is the Off position. In the off position, voltage is not supplied to the rest of the circuit. Terminal 87A is the center terminal on the relay.
- When the PCM energizes the ASD and fuel pump relays, terminal 87 connects to terminal 30. This is the On position. Terminal 87 supplies voltage to the rest of the curcuit.

TESTING
The following procedure applies to the ASD and fuel pump relays.
(1) Remove relay from connector before testing.
(2) With the relay removed from the vehicle, use an ohmmeter to check the resistance between terminals 85 and 86. The resistance shoud be 75±5 ohms.
(3) Connect the ohmmeter between terminals 30 and 87A. The ohmmeter should show continuity between terminals 30 and 87A.
(4) Connect the ohmmeter between between terminals 87 and 30. The ohmmeter should not show continuity at this time.
(5) Connect one end of a jumper wire (16 guage or smaller) to relay terminal 85. Connect the other end of the jumper wire to the ground side of a 12 volt power source.
(6) Connect on end of another jumper wire (16 guage or smaller) to the power side of the 12 volt power source. Do not attach the other end of the jumper wire to the relay at this time.

WARNING: DO NOT ALLOW OHMMETER TO CONTACT TERMINALS 85 OR 86 DURING THIS TEST.

(7) Attach the other end of the jumper wire to relay terminal 86. This activates the relay. The ohmmeter should now show continuity between relay terminals 87 and 30. The ohmmeter should not show continuity between relay terminals 87A and 30.
(8) Disconnect jumper wires.
(9) Replace the relay if it did not pass the continuity and resistance tests. If the relay passed the tests, is operates properly. Check the remainder of the ASD and fuel pump curcuits.

__________________________________________________ _______________

I know you said you replaced the relay, and this is a test procedure for the relay, but I have bought bad parts in the past. The description before the test procedure at least gives you an idea of what components are wired through and controlled by the relay. One of those may be faulty. Email me if you want or need wiring diagrams and I should be able to scan them and email them to you.

Jul 15, 2015 | 1992 Dodge Dakota

3 Answers

I have a 02 grand caravan, there is fuse call asd that keeps on blowing.


Well in a short term, you have a short circuit somewhere. Here is a detailed toturial for you. Please rate this post, thank you.

Automatic Shutdown (ASD) sense - PCM Input

The ASD sense circuit informs the PCM when the ASD relay energizes. A 12 volt signal at this input indicated to the PCM that the ASD has been activated. This input is used only to sense that the ASD relay is energized.
When energized, the ASD relay supplies battery voltage to the fuel injectors, ignition coils, and the heating element in each oxygen sensor. If the PCM does not receive 12 volts from this input after grounding the ASD reley, it sets a Diagnostic Trouble Code (DTC).

Automatic Shutdown Relay - PCM Output

The PCM operates the Automatic Shutdown (ASD) relay and fuel pump relay through one ground path. The PCM operates them by switching the ground path for the solenoid side of the realys on and off. Both realys turn on and off at the same time.
The ASD relay connects battery voltage to the fuel injectors and ignition coil. The fuel pump relay connects battery voltage to the fuel pump.
A buss bar in the power distribution center (PDC) supplies voltage to the solenoid side and contact side of the relay. The ASD relay power circuit contains a 20 amp fuse between the buss bar in the PDC and teh relay. The fuse also protects the power circuit for the fuel pump relay and pump. The fuse is located in teh PDC.
The PCM controls the relay by switching the ground path for the solenoid side of the relay on and off. The PCM turns the ground path off when the ignition switch is in the Off position. When the ignition switch is in the On or Crank position, the PCM monitors the crankshaft position sensor and the camshaft position sensor signals to determine engine speed and ignition timing (coil dwell). If the PCM does not receive the crankshaft position sensor and camshaft position when the ignition switch is in teh Run position, it will de-energize teh ASD relay.
The ASD relay and fuel pump relay are located in the PDC near the battery. The inside top of the PCD cover has a label showing relay and fuse location.

ASD and Fuel Pump Relays

The following description of operation and tests apply only to the Automatic Shutdown (ASD) and fuel pump relays. The terminals on the bottom of each relay are numbered.

'------------------'
' __85 ___________'
' __87A '87 '30 ___' Sorry for the crudeness of this. This is supposed to
' __86 ___________' be the relay terminals!
'------------------'

OPERATION
- Terminal number 30 is connected to battery voltage. For both the ASD and fuel pump relays, terminal 30 is connected to battery voltage at all times.
- The PCM grounds the coil side of the relay through terminal number 85.
- Terminal number 86 supplies voltage to the coil side of the relay.
- When the PCM de-energizes the ASD and fuel pump relays, terminal number 87A connects to terminal 30. This is the Off position. In the off position, voltage is not supplied to the rest of the circuit. Terminal 87A is the center terminal on the relay.
- When the PCM energizes the ASD and fuel pump relays, terminal 87 connects to terminal 30. This is the On position. Terminal 87 supplies voltage to the rest of the curcuit.

TESTING
The following procedure applies to the ASD and fuel pump relays.
(1) Remove relay from connector before testing.
(2) With the relay removed from the vehicle, use an ohmmeter to check the resistance between terminals 85 and 86. The resistance shoud be 75±5 ohms.
(3) Connect the ohmmeter between terminals 30 and 87A. The ohmmeter should show continuity between terminals 30 and 87A.
(4) Connect the ohmmeter between between terminals 87 and 30. The ohmmeter should not show continuity at this time.
(5) Connect one end of a jumper wire (16 guage or smaller) to relay terminal 85. Connect the other end of the jumper wire to the ground side of a 12 volt power source.
(6) Connect on end of another jumper wire (16 guage or smaller) to the power side of the 12 volt power source. Do not attach the other end of the jumper wire to the relay at this time.

WARNING: DO NOT ALLOW OHMMETER TO CONTACT TERMINALS 85 OR 86 DURING THIS TEST.

(7) Attach the other end of the jumper wire to relay terminal 86. This activates the relay. The ohmmeter should now show continuity between relay terminals 87 and 30. The ohmmeter should not show continuity between relay terminals 87A and 30.
(8) Disconnect jumper wires.
(9) Replace the relay if it did not pass the continuity and resistance tests. If the relay passed the tests, is operates properly. Check the remainder of the ASD and fuel pump curcuits.

__________________________________________________ _______________

I know you said you replaced the relay, and this is a test procedure for the relay, but I have bought bad parts in the past. The description before the test procedure at least gives you an idea of what components are wired through and controlled by the relay. One of those may be faulty. Email me if you want or need wiring diagrams and I should be able to scan them and email them to you.

I hope this helps.

Please rate this post, thank you

Apr 07, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

Where is the asd relay on my 1990 dakota?


ASD is in the engine compartment fuse block.

The pump relay should be there also. Check your fuse panel in the truck though.

Fuses, Relays & Circuit Breakers The fuse panel box is to the right of the glove box with the glove box door opened or beneath the instrument panel (dashboard) on 1989-93 models.

2d26fdd.gif
Pull out the fuse panel for access to the blade type fuses

Oct 18, 2009 | 1990 Dodge Dakota

1 Answer

On 1996 dodge grand caravan code 42 from blinks from chedk engine light.


A code 42 is the Auto Shutdown Relay Control Circuit....The ASD relay is located under the hood in the Power Distribution Center next to the battery. Change the ASD relay, that should fix you up. If that doesn't work...you might have to check the PCM. But replacing the ASD relay should do it.

Bryon

Oct 11, 2009 | 1996 Dodge Caravan

1 Answer

Engine won't start


Sounds like an AUTOMATIC SHUTDOWN (ASD) RELAY problem. Fairly common on the Caravan.
Heres a brief overview of the ASD.
The Powertrain Control Module (PCM) operates the Auto Shutdown (ASD) relay by switching the ground path on and off.
The ASD relay supplies battery voltage to the fuel injectors, electronic ignition coil and the heating elements in the oxygen sensors.
The PCM controls the relay by switching the ground path for the solenoid side of the relay on and off. The PCM turns the ground path off when the ignition switch is in the Off position unless the 02 Heater Monitor test is being run. Refer to On-Board Diagnostics. When the ignition switch is in the On or Crank position, the PCM monitors the crankshaft position sensor and camshaft position sensor signals to determine engine speed and ignition timing (coil dwell). If the PCM does not receive the crankshaft position sensor and camshaft position sensor signals when the ignition switch is in the Run position, it will de-energize the ASD relay.
The ASD relay is located in the Power Distribution Center (PDC). The PDC is located on the driver's side inner fender well Power Distribution Center . A label on the underside of the PDC cover identifies the relays and fuses in the PDC
Check for good ground.
Good luck...i hope this helps, please rate me a fixya.

Jun 25, 2009 | 1994 Dodge Caravan

1 Answer

No reverse only drives for 30 seconds limp mode???? please help!


P1388 = Auto Shutdown (ASD) relay control circuit open or shorted.
The ASD relay routes battery power to the ignition coils, and is energized by the PCM as long as it receives signals from both the crankshaft and camshaft position sensors. If the engine stops turning (stalls), the PCM deengerizes the ASD relay and shuts down the ignition system. The ASD relay also supplies battery voltage to the fuel injectors, so when it shuts down it cuts off both ignition and fuel. At the same time, the PCM also deenergizes the fuel pump relay to turn off the fuel pump. For "limp in" capability, the Chrysler system can run with input from the crankshaft position sensor only. The ASD and fuel pump relays are both located in the Power Distribution Center.

May 10, 2009 | Chrysler Voyager Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...