Question about 2005 Hyundai Accent

Open Question

Clutch slave cylinder smoking and making noise

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnthejag
  • 286 Answers

SOURCE: bleeding the slave cylinder

Hi

Best to get the help of a friend to pump the clutch pedal for you.

Take care with the brake fluid, as it removes paintwork !

Top up your clutch fluid reservoir, connect a bleeding tube to the nipple on your slave cylinder, and put the other end of tube in a container.

Get your friend to pump pedal 3 times, and then hold to the floor.

Open the nipple for 5 seconds or so, then close.

Repeat this about 6 to 8 times topping up the fluid as you go.

You should then find, that the air is out of your system, and your pedal is back to normal !

Good luck !

A FixYa rating would be nice.... Thank you ! John.



Posted on Feb 10, 2009

Ad
  • 566 Answers

SOURCE: 1997 hyandai accent gt clutch problem

hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

Posted on May 15, 2009

  • 6982 Answers

SOURCE: leaking clutch fluid Where is the slave cylinder"..I have been told to look at the slave cylinder because I do not see fluid under the car.

Slave cylinder should be on the left side of the bellhousing (follow the line from the clutch master if necessary) If you don't see fluid but you have lost some, also check where the rod from the pedal goes through the firewall to the master...they often leak there and will not drip on the ground.

Posted on May 30, 2009

  • 2418 Answers

SOURCE: Clutch is not working. Pedal goes all the way to

Have noticed a leak in the area of your slave cyl? You you have a new one will fix the problem. just install it add fluid, bleed it, ( add fluid reinstall the cover, have someone help or just take the bleed screw loose let the new fluid drain thru. get in and pump the pedal ck the fluid in the res. add fluid. keep this back and forth till you feel a good pedal. done. Work slow, be careful.

Posted on Jul 03, 2009

SOURCE: 2003 Hyundai Accent clutch slave cylinder problem

dear friend-the spring and valve came from the back where the bolt goes in . it is a compensating valve.you put it back valve first then spring or you can leave it out.it makes no differense

Posted on Jul 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?


a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




26351104-h2ljceqgvzc5xcxajl4olrsz-4-0.jpg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-1.jpeg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-3.jpg

Nov 11, 2016 | 2004 Ford Focus

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

3 Answers

The clutch was having a hard time going into gear.All of a sudden there was a high pitched squeal/scream coming from the transmission area.


that sounds like a throw out bearing failure-is there any adjustment at the slave cylinder-it may be holding the bearing against the clutch and causing the noise-this thread may help-http://www.jeepforum.com/forum/f9/how-change-bleed-clutch-slave-cylinder-511531/- cheers Denny

Dec 22, 2013 | 2000 Jeep Wrangler

1 Answer

Where is the slave cylinder for the clutch located. internal or externaly.


First thing to do is to see if you have a clutch slave cylinder or cable operated clutch. Second the slave cylinder is on the end of the lever that goes into the clutch housing Before you change the clutch make sure that the problem is not in the slave cylinder or clutch master cylinder or cable as the case may be.

Jun 09, 2013 | 1998 Dodge Avenger

1 Answer

Clutch problems


Hi bosslady15,

First of all I think I should say that clutches do not make grinding noises - but transmission gears do.
However, a clutch that is not disengaging properly can make the gears grind when trying to shift from one gear to the next. Also a common source of noise is the clutch throwout bearing. This will make a "grinding" or "growling" noise any time the clutch pedal is depressed. In either of these cases, the only solution is to replace the clutch, throwout bearing, pressure plate and pilot bushing. These all usually come in a clutch kit. If you have an hydraulic clutch with an internal slave cylinder it is recommended to replace the slave cylinder as well and also the flywheel on on vehicles. I'm sorry I cannot be more specific because you did not mention what type of vehicle we are talking about here.

Nov 07, 2011 | Cars & Trucks

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

Replaced slave cylinder, now grinds


the forck for the throwout bearing has fell off the pin it is not that hard to put back on take slave cyld back off then feel of the forck you can tell where it needs to be pop it back in

Feb 14, 2009 | 1997 Jeep Wrangler

2 Answers

89 ranger manual trans slipping already replace clutch and slave cylinder? still slipping any help?


Manual transmissions do not slip ie. when the gears mesh, there is no slip unless they strip out and make an awful noise and will not pull henceforth.

You probably still have a slipping clutch plate against the flywheel. You need to adjust the clutch petal linkage shaft to allow the pressure plate to be release from the thrust bearing, ie shorten the shaft length.. If you and most likely you do just have the clutch release slave cylinder that releases the clutch when you apply the petal. You need to bleed the slave cylinder of any excess fluid or air that may have entered the line if you opened it at any point. You need to bleed it as you would a break cylinder and this should fix ya.
good luck.
good luck

Jan 05, 2009 | 1989 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...