Question about Cars & Trucks

Open Question

Location of glow plug control module for 2009 e320

Have a U0106 DTC code and need to replace the glow plug control module on my 2009 e320 bluetec. Trying to find the location of the control module.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75077 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

relaga58
  • 158 Answers

SOURCE: 1997 nissan altima has no spark at the plugs.

get those sensors connected to the output of the module tested cause its ruining the module

Posted on May 10, 2009

c17hydro
  • 2984 Answers

SOURCE: try to locate body control module on a 94 buick park ave

BCM --The Body Control Module is located on the right side of the vehicle and positioned under the instrument panel. In order to gain access to the module, it will be necessary to first remove the trim panel.

Posted on Jun 23, 2009

  • 4 Answers

SOURCE: peugeot partner wopnt start replaced glow plug

what voltage u getting ?. did it just stop and then not restart. if its getting fuel and glow plugs are working the next two items id look at is the cam shaft and crank shaft position sencors. also make sure ur battery is in good condition, so starter motor is turning fast enough to build up the correct pressure on the rail.

Posted on Dec 14, 2009

  • 412 Answers

SOURCE: i have replace alternator & glow plug control

i believe there is an issue with the positive battery cable.. cable coming from the battery to starter..alternator gets feed from starter battery post..i have seen this problem before..check battery feed to alternator..if 12v is not at alternator main feed wire(large wire)..it will not charge..you will need positive cable from battery to starter..i hope this helps

Posted on Jan 11, 2010

Testimonial: "thank you that was helpful , fix my problem."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2009 Chevy Avalanche LS and I got the P0700 code, how easy is this to fix? where is the TCM located? If this is a dealer service how much?


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination
The transmission control module (TCM) uses the (GMLAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure affecting emissions has occurred in transmission control system. When the ECM receives the message from the TCM, DTC P0700 will set.
DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.
This is something best left to a qualified repair shop , doesn't need to be the dealer ! AMMCO could fix it . This code is telling that other codes are stored in the transmission control module . Need a professional type or factory scan tool to check these . As to how much it will cost , no telling without knowing the codes in the TCM !

Apr 28, 2017 | Cars & Trucks

1 Answer

2006 chevy silverado duramax hd 4WD has codes u1016 /c0035/co201/po673/675/677 but runs great


DTC P0671: Cylinder #1 Glow Plug Control Circuit
DTC P0672: Cylinder #2 Glow Plug Control Circuit
DTC P0673: Cylinder #3 Glow Plug Control Circuit
DTC P0674: Cylinder #4 Glow Plug Control Circuit
DTC P0675: Cylinder #5 Glow Plug Control Circuit
DTC P0676: Cylinder #6 Glow Plug Control Circuit
DTC P0677: Cylinder #7 Glow Plug Control Circuit
DTC P0678: Cylinder #8 Glow Plug Control Circuit

Circuit/System Description
The glow plug controller has the ability to perform internal checks, an open or a short to ground on each of the glow plug circuits. If the glow plug controller senses a problem in a glow plug circuit, the glow plug on the affected cylinder will be disabled and the glow plug controller will send an error message to the engine control module (ECM). If this condition exists, the DTC will set.
Conditions for Setting the DTC
The glow plug controller detects that the glow plug control circuit is open, shorted to ground, or has more than 1 ohm of resistance.

Circuit/System Verification
Verify that DTC P064C is not set.
If DTC P064C is set, refer to DTC P064C.
Ignition ON, engine OFF, observe the scan tool Glow Plug 1-Glow Plug 8 parameters. All 8 Glow Plug parameters should closely match each other.
Refer to Testing for Intermittent Conditions and Poor Connections if you cannot duplicate the conditions.
Engine running, observe the DTC information with a scan tool. DTCs P0671-P0678 should not set.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

DTC C0035 Left Front Wheel Speed Sensor Circuit
DTC C0201 Antilock Brake System (ABS) Enable Relay Contact Circuit
The system relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids and to the ABS pump motor. When the relay contacts close, the EBCM monitors the voltage supplied to the valve solenoids and compares this voltage to monitored ignition voltage.

Jul 30, 2016 | Cars & Trucks

1 Answer

Code u0106 what to look for


Possibly a bad glow plug control module. 25330906-xrysbksmd4oe40lchygmaasz-5-0.jpg

Dec 20, 2014 | Cars & Trucks

2 Answers

What is the code p0473 for a dodge sprinter van 2008


Error Code: P0404
Fault Location:
Exhaust Gas Recirculation (EGR) System - Range/Performance Problem
Causes:
-Hose leak/blockage.
-Wiring harness.
-Exhaust gas recirculation (EGR) valve/solenoid.
Error Code: P0473
Discription:
Exhaust Gas Pressure Sensor - High Input
Causes:
- Wiring short to positive.
- Exhaust gas pressure sensor (G450).
- Engine control module (ECM).
Error Code: P0674
Description:
Glow Plug Cylinder 4 Circuit - Circuit Malfunction
Causes:
-No Pre-Glow Period.
-Poor Cold Starting.
-Glow Plug Wiring faulty.
-Poor connection.
-Relay.
-Glow plug control module.
-Glow Plug faulty.
-Engine control module (ECM).
Solutions:
Check Glow Plug Wiring.
Check Glow Plug.
Error Code: P0675
Description:
Glow Plug Cylinder 5 Circuit - Circuit Malfunction
Causes:
-No Pre-Glow Period.
-Poor Cold Starting.
-Glow Plug Wiring faulty.
-Poor connection.
-Relay.
-Glow plug control module.
-Glow Plug faulty.
-Engine control module (ECM).
Solutions:
-Check Glow Plug Wiring.
-Check Glow Plug.

Sep 20, 2014 | 2008 Dodge Sprinter

1 Answer

Glow plug DTC light


glow light bulb could be burned out.but glow plugs is control by ECM AND RELAY.do your vechicle start but you dont see glow plug light on to let you know glow plugs are energized heating up.also check glow plug fuse, look in owner manual in glovecompartment it will show all fuses and relays locations.

Nov 07, 2012 | 2005 BMW X5

1 Answer

What does the codes 0627-0681-0680-0688 on 2006 chrysler sebring 2.4 16 valve 4 cly


Hi there:

DTC P0627 CHRYSLER - Fuel Pump Relay Control Circuit
ECM (Engine Control Module) detected an open or short in the fuel pump relay circuit
Possible causes
- Fuel pump circuit open or short
- Fuel pump circuit poor electrical connection
- Faulty fuel pump relay
- Faulty fuel pump control module (if applicable)


DTC P0680 - Cylinder 10 Glow Plug Circ, and,

DTC P0681 - Cylinder 11 Glow Plug Circ
The Engine Control Module (ECM) has detected a fault in the cylinder #10 or #11 glow plug circuit.


Possible causes
- Cylinder #10, or #11 glow plug circuit is open or shorted
- Faulty cylinder #10 or #11 glow plug
- Faulty glow plug module Help with this


DTC P0688 CHRYSLER - Auto Shutdown Relay Control Circuit Low

The Front Control Module (FCM) has detected the supply voltage below an acceptable value.

Possible causes
- ASD relay circuit is open or shorted
- Failed Auto Shutdown relay
- Failed ECM


Check all the ECM fuses, if the fuses are OK try replacing the ASD relay.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 03, 2012 | Chrysler Sebring Cars & Trucks

1 Answer

WHAT IS DTC-01 P0673 ON A 2500 HD


OBD Code P0673refers to
The Engine Control Module (ECM) has detected a fault in the cylinder #3 glow plug circuit SymptomsPossible sumptoms of OBD code P0673
- Engine Light ON (or Service Engine Soon Warning Light) - Lack/Loss of Power - The engine may be harder to start - Engine hesitation CausesPossible causes of OBD code P0673
- Cylinder #3 glow plug circuit is open or shorted - Faulty cylinder #3 glow plug - Faulty glow plug module

Jul 09, 2011 | GMC Sierra 2500HD Cars & Trucks

1 Answer

PO380 and p1316 what do thies coads mean.


P0380 - Glow Plug/Heater Circuit "A" Malfunction
Bad glow plug. The glow plug system is used to assist in providing the heat required to begin combustion during cold engine temperatures. The glow plugs are heated before and during cranking, as well as initial engine operation. The engine control module (ECM) controls the glow plug ON times by monitoring coolant temperature and glow plug voltage. The California Glow Plug system has eight individual glow plug supply circuits between the controller and the glow plugs. If the feedback voltage from the controller to the ECM is not within range, DTC P0380 will set.

- The glow plugs are commanded OFF and the glow plug feedback is more than 2 volts. or
- The glow plugs are commanded on and the glow plug feedback is not between 5 volts and 6.2 volts.

Keep in mind that the "wait to start" light only comes on while the voltage is dropping in that circuit. This should only take 3-5 sec's. If it takes longer, refer to your "Likely problem" you listed above. That would be the Heater Module. If your glo plugs stay on, your batteries would be dead in no time. If any of your plugs go bad, they would each be listed on the reader per cyl 1-8. If you need to change the Module,


P1316 - Injector Circuit / IDM Codes Detected.
This code indicates that codes are stored in the IDM

Possible causes are as follows:
- Injector(s) or circuit(s)
- Open or shorted IDM enable circuit
- Open/short in EF circuit
- Open/short in FDCS circuit
- IDM relay
- IDM powering circuits
- Failed IDM
- Failed PCM

Check your Injector Driver Module wires, circuits 821 (Brown/Orange) and 818 (Grey/White) between the PCM and IDM. On the IDM side, the connector pin numbers are 17 for circuit 821, and pin 4 for circuit 818. You should check for high resistance in that circuit, short to ground, or open circuits. If wiring checks out good, you may need to replace your IDM. It's not uncommon for water intrusion into the module, due to its mounting location. Also check the engine wiring harness where it routes up over the driver side shock and/or driver side valve cover. That code is either a key-on/engine-off or a continuous memory code.


Hope this helps (remember to rate this answer).

Feb 04, 2011 | 1999 Ford F350 Regular Cab

1 Answer

Glow Plug system diagnosis


I HAD SAME CODE TO BUT NOTE THE CODES MIS READING DUE TO THIS Check under seat unplug control module see if it is wet with fluid . cost me $138.00 fee.
Engine light on than next day off may 2 day then on at same place drive kid to school.
issue with transmission fluid wicking up the harness into the control module and causing the module to malfunction. Usually, the harness from the transmission to the ETC module is replaced and the module is replaced provided the leak is repaired. In some cases this may be more than is actually needed but it usually fixes the concern. Transmission fluid does not actually damage the module and can be flushed away with board cleaning solvent or electrical contact cleaner as a first attempt. Always repair the leak before replacing a module.
http://www.benzworld.org/forums/w163-m-class/1465231-mercedes-repair-maintainance-transmission-etc-tips.html

Jul 19, 2010 | 2006 Dodge Sprinter

1 Answer

Need radio code for 1995 Mercedes Benz E320 sedan


Its inside your car manual on the left side as you open it up, it'll be a lil grey card that will have the radio code written on it... read the manual and it'll tell you how to put the numbers in.

Mar 16, 2010 | 2007 Mercedes-Benz E320 BLUETEC Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...