- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
set mark on crankshaft to TDC mark on timing cover. set mark on cam pulley to align with mark on head .if more than one mark on pulley rotate by hand till exhaust and inlet just rocking then align closest marks .
Double check crankshaft timing mark, on your lower timing cover has some timing marks - crankshaft should be on the 0 mark. Camshaft timing marks--intake camshaft mark set at 3 o'clock and exhaust camshaft mark set a 9 o'clock. These timing marks are critical for motor to run and start correctly. These timings marks can move while trying to install the timing belt. After, you confirm or reset timing and belt, you can confirm timing is correct by rotating the crankshaft twice. Your timing marks should be on right on timing marks discussed at the top of the page. If timing marks are off, start over with timing process.
its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok
set the timing mark on the crankshaft to the mark on the oil pump, then set the timing mark on the camshaft to the mark on the alternator bracket/set second camshaft mark to mark on the inner timing belt cover. line up all mark as decribed. be sure before u set anything to bring #1 piston all the way up to top. with belt on turn crankshaft 2 full turns to bring #1 piston back to top if the cams are not lined up correctly loosen belt and start over again until everything lines up correctly. you may have to do this a few times but it will work.
Installation Ensure timing marks aligned  &  . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt  . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt  . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned  . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt  . Tightening torque: 170-180 Nm
7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top
The mechanic should check on the timing mark . sir you have to look at the timing mark to set the timing chain .there is a timing mark in the pulley where you will place the timing chain.and then there also is a timing mark in the place where you place the pulley set it both align with each other then after it then place the belt.then it is set.
or the timing marks? the timing marks differ. best set cyl. no 1 to tdc.. take out no. 1 spark plug and put sumthin long and thin down the hole.. like a long quarter drive extension.. and check to see that cyl 1 is at tdc.. then set your cam to the OT marks marked on the cam pulley and rocker cover... then you have to set the distributor also.. slacken the 13mm bolt for the dizzy clamp... you will find a line on the lip of the dizzy body.. this needs to align with the middle of rotor arm tip... (sumtimes a mark on the roror arm tip)... tension belt and your timing is set.. set your timing incorrectly and the car will run rough and not rev past 5k...