Question about Cars & Trucks

Open Question

How to repair brake master cylinder

Opel monza automatic

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 232 Answers

SOURCE: Spongy brakes after bleeding them 2 times. Should I try to bleed the master cylinder or replace it?

Honestly your guess is as good as mine. But I don't think the master cylinder is NOT bad you still have air in the system. Get a big bottle of brake fluid bleed all four sides until you run out of fluid or your brakes work properly. You should divide the bottle's content in four, then use each quantity in each side. You'll be removing air and contaminated fluid from the system. Get a small hose that fits on the bleeders and an appropriate container. I have a good feeling if you do this your brakes will work just fine. I don't know how you are bleeding the brakes. I'll let you know the proper way just in case. This is a two man job, with the wheel off, have someone start the car. Have them pump the brakes a few times to get pressure. 1With the brake pedal UP open the bleeder, 2then have your assistant press the brake pedal all the way down and leave it completely pressed down. 3Close the bleeder valve, once close and only with the valve closed have'm release the brake. Repeat as necessary, bake depressed, open valve first then press brake. DO NOT depress until valve completly closed. Close valve THEN depress. Good Luck!

Posted on May 15, 2009

  • 249 Answers

SOURCE: toyota brake problem

the prob is still your master cylinder. the seal sounds like its back on its self or there is a wear line that pushes it back, get 1 from a scrapy that works, fit undo the rear nipples and leave to drip for 5 mins . then do the front, look at the rear load compensator some vehicles have a bleed nipple to release trapped air from there, what happens when nipple open and u push pedal.

Posted on Aug 16, 2009

  • 38 Answers

SOURCE: I'm looking for a electrical diagram for a 1990

This is the only legitimate source I could find.
http://www.opelownersforum.co.za/forum/viewforum.php?f=8

Register there, and good luck!

Posted on Sep 19, 2009

  • 189 Answers

SOURCE: remove master cylinder 1996 dodge caravan 2.4

disconnect brake lines from MC should be only 2. Remove the 2 nuts holding the MC on. replace in reverse order u will need to bench bleed the new MC and u will probaly need to bleed the brakes

Posted on Apr 14, 2010

SOURCE: 1994 Crown Victoria: need to add brake fluid to master cylinder...

Why would you add fluid?
As the front pads wear,the fluid will go down, not an issue
If you keep opening the fluid resevoir,you will let moisture in.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Opel monza gsi E16ES ecu pinout wiring diagram


The ecu doesn't control the power of the spark, only where it goes at a particular time. The coil/s, plugs, wires, cap and rotor do though.

Dec 27, 2014 | Opel Cars & Trucks

1 Answer

Workshop manual for opel monza 1600 gsi


Wow thats a old vehicle ,remember working on a 3 litre version many years ago but a workshop manual ??

Dec 06, 2014 | Opel Cars & Trucks

1 Answer

Why my opel monza Gsi 160 i using a lot of fuel


If the emissions are OK, and the car is running OK then it's either leaking fuel or you need to drive more gently. They aren't a particularly economical car

Jun 22, 2014 | Opel Cars & Trucks

1 Answer

Timing belt diagrams opel monza


Opelopel monza ohc single cam

May 01, 2013 | Cars & Trucks

1 Answer

No spark on opel monza 160 gsi what could the problem be?


failing dispack you should have the engine codes read and see if this is the only problem.

Sep 23, 2012 | Opel Cars & Trucks

1 Answer

Need a diagram circuit of opel monza


this is the only schematic I can find, hope it helps :)
http://www.totalopel.com/forum/showthread.php?t=3753
this is an Opel message board, you might want to sign up with them as I am sure they can give better info. good luck

May 29, 2012 | 1977 Opel Kadett 2.0

2 Answers

Torque settings


dear friend:
flywheel: 35nm - 30deg -15deg
cyl head:55nm - 30deg cold
big ends:25nm - 15deg
main b :50nm - 45deg -15deg

Sep 15, 2009 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...