Question about Cars & Trucks

Open Question

2000 chrysler concorde wont start

My car just cut off on me while I was driving one day. I pulled over and immediately tried to re-start it. It made the noise as if it were going to start up but it never turned over. I took it to a guy that does mechanic work and he suggested that it may have been the crank sensor so I purchased one of those and had that replaced. The car still will not crank. He also checked the timing change and the fuel pump and those two items were ruled out. He suggested that I take it to the dealer to get it resolved. Anyone have any possible solutions prior to me doing that?

Posted by on

  • Melanie
    Melanie Apr 16, 2014

    I wanted to come back and let everyone know what the problem was with my car. The crank sensor was one of the problems. The first one that I purchased and was put on my car was a faulty one. The other issue was the crank sham sensor and the timing had jumped a couple of notches. So, it was a $1,000.00 repair job but I haven't had any problems with my car sense. I got the repairs done back in late January or Early February 2014. I hope this helps someone.



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 chevy blazer, truck cranks

Does your battery go dead?

Posted on Dec 18, 2008

  • 115 Answers

SOURCE: 2000 Chrysler Concorde

These engines are known for the water pumps and/or the timing chains hydraulic tensioner failing and causing the timing to jump time. And checking the timing on these engine is not easy unless you can get a scan tool that can tell you if the cam and crank are in sync. If it says out of sync it has most likely jump time.

Posted on Feb 16, 2009

  • 100 Answers

SOURCE: I recently replace the crank shift sensor, but

switch on your car but don't start it, let it stay in that position for a few minutes. after start your car, if starts without problems then your problem is your fuel pump. but if problem is still there then it could be your fuel filter or timing of your car.

Posted on Apr 24, 2009

  • 101 Answers

SOURCE: chrysler wont start

Sounds like a short maybe. maybe the wire completely broke? if you know a technician, see if the fuel pump is even getting power when key is on

Posted on Jul 02, 2009

  • 6927 Answers

SOURCE: 94 concorde

change crank sensor? if so replace control module (ignition module)

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Car cut off suddenly and won't start

have you tried if the engine rotates or not. and why you ruled out the timing belt?

Oct 30, 2017 | 2000 Chrysler Concorde

2 Answers

Concorde clicking start or wont start

-You mean click but no crank (Turn over).
If so. Need new starter.


Nov 11, 2013 | 2000 Chrysler Concorde

1 Answer

2000 chrysler concorde check engine light came on, dash lighs flash and transmission wont shift any ideas?

It sounds like you have a problem with your security system if you mean that it won't allow you to shift out of park. BUT you should start off getting the engine error code read so you will know what the car is trying to tell you. Anytime you get a check engine light, the vehicle generates an error code.

Since you probably can't drive it, you need to rent, borrow or buy an OBDII scanner and get that code, so it gives you a clue on where to begin the troubleshooting process.

Jul 04, 2011 | 2000 Chrysler Concorde

1 Answer

How do i open the hood on a 2000 chrysler concorde lxi if the latch cable is cut?

You must go through the front grill. If you cant do that try under the front of the car so you can reach the latch

Feb 02, 2010 | 2000 Chrysler Concorde

1 Answer

95 concord wont start at times

how do i install a new ignition switch on my 95 chrys conc

Dec 29, 2009 | 1995 Chrysler Concorde

1 Answer

2003 concorde,when after starting cold and i have

when was the fluid and filter in transmission changed ?

Aug 06, 2009 | 2003 Chrysler Concorde

1 Answer

Car dies while driving. Will start up after 20 to

My 2000 Chrysler Concorde does the same exact thing. Had the shop put a computer on the car and the oxygen sensor was out of whack but that didn't give them much help on a solution. They think it's the fuel pump, but don't want to work on it until a better lead is found. Did you try anything that worked?

Jul 09, 2009 | 2000 Chrysler Concorde

2 Answers

Starter clicks car wont start. Plastic metal smell.

the starter it self......if it doesnot crank it is the starter........

the starter probably has one or two chipped teeth..."if you can try going under ur car and remove the starter......

hope this helps man ! XD

May 14, 2009 | 1994 Chrysler Concorde

1 Answer


more than likely it could be a crank postion sensor but more than likely the tranny is slipping or having torque converter failure.

Mar 10, 2009 | 2000 Chrysler Concorde

2 Answers

2001 concorde dont start

Check the cranshaft position sensor located under the timing cover. Also check the camshaft sensor located near the camshaft.

Feb 06, 2009 | 2001 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides