Question about GMC Sonoma

Open Question

Cruise control not working on 2002 gmc sonoma

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: cruise control won't work

Does the on light in the dash come on? If not, you may have a broken switch in the steering wheel which is a fairly cheap repair. Otherwise, the controls work through the Printed Circuit Board in your dash (your instrument cluster) and the problem could be as simple as a solder defect or faulty component. The problem is that no Ford Service Technician that I know will touch this and tell you that you need to replace it.

The instrument cluster is very easy to replace but may cost you a few more dollars than you want to spend. I would have someone with an electrical background check the cruise control switches in your steering wheel with a multimeter before going any further with this. Also check the wiring for resistance leading from the switch to the cluster.

Posted on Aug 06, 2008

Ad
Hrnsly
  • 154 Answers

SOURCE: the cruise control is not working 2002 Mazda Tribute

you have a bad cruise cable, this is a very common problem with the tribute. just go to your local dealer and have them replace it for you, it only takes about 30 minutes to do

Posted on Aug 13, 2009

  • 432 Answers

SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control

May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Posted on Feb 05, 2010

sscullys
  • 984 Answers

SOURCE: 2002 Ford F150. Cruise control stopped working.

Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Posted on Feb 23, 2010

ryanlutton
  • 1131 Answers

SOURCE: I have a 2002 GMC

Most times when this happens with Envoys and Trailblazers, your PCM or computer is storing a check engine code, which will disable cruise control. Scan your vehicle with an OBDII scanner to see what code may be stored. Once the code is cleared, your cruise control will work again.

Posted on Dec 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 sonoma air temperature stays hot when i turn the control knob. A/C works fine,but the air does'nt get cooler when I turn the knob


Easiest place to start is checking for a broken control knob. Pull the knob off and see if it is cracked/broken on the back side. You can turn the metal control rod then by hand to see if it works. If no problem found there, you will have to check for a blend door motor/actuator that controls heat/cooling attached to the heater box under the dash for proper operation

Jan 06, 2016 | 2002 GMC Sonoma Extended Cab

1 Answer

Cruise control not working in drive, but works in overdrive?


it could be a problem with the brake switch ajustment.
pcm know witch gear is on ,,,alloy the cruise control to works
you need with a scanner look at data to see cruise on/off system

hope it helps

Sep 27, 2014 | 2002 GMC Envoy

1 Answer

Engine reduced power


Reduced power can be a multitude of things. Find out what code is present by using a scanner. The cruise control WILL NOT work if the check engine light is on. Once the check engine light is cleared, the cruise control will work again.

Nov 23, 2013 | 2002 GMC Envoy

1 Answer

I have a 2002 GMC Envoy and the cruise control not working now. Worked before


Most times when this happens with Envoys and Trailblazers, your PCM or computer is storing a check engine code, which will disable cruise control. Scan your vehicle with an OBDII scanner to see what code may be stored. Once the code is cleared, your cruise control will work again.

Dec 21, 2010 | 2002 GMC Envoy

1 Answer

My 2002 gmc sonoma will not turn over I have changed the battery


check the cables to the starter might be loose...check nutural safety swith on the transmission..

Mar 09, 2010 | 2002 GMC Sonoma Extended Cab

1 Answer

How do I replace the switch in my turn signal that controls the bright lights in my 1991 gmc sonoma


Take the cover off of the steering colum and the whole lever pops in where the switch is and you just change out the whole thing if you have cruise control there will be a wire with a connector that you have to disconnect and then reconnect the new one.

Jul 01, 2009 | 1991 GMC Sonoma

1 Answer

I cant find the fuse for the cruise control on my 1992 gmc sonoma


Are you sure your truck is a) 1992 and b) a Sonoma. ?
The 1994 Sonoma CC fuse is the same as the Brake fuse. See below:

c3ac955.jpg

Apr 29, 2009 | 1992 Chevrolet S-10

2 Answers

Need wiring diagram for 1996 GMC Sonoma, I lost all electrical power( no accessories, none),I have 12.67 volts to the starter and alternator, fuse links to this components checked good. is there some kind...


i have had same problems i can turn key on radio works and everything else i have found that problem with mine to be a short ground out from the main power lead from the battery to the starter that was shorting it out until i moved it around and found it

Apr 19, 2009 | 1996 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...