Question about Chevrolet Impala

Open Question

Remove kick panel - Impala Chevrolet Cars & Trucks

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is a driver side kick panel?

The interior trim panel down at floor level in front of the door. It is the side panel down where your feet go.
Remove this kick panel and you are likely to see the ground point for the power windows. Sometimes manufacturers put relays behind this panel, too.

Apr 27, 2017 | Cars & Trucks

1 Answer

Remove passenger kick panel

passenger kick panel Debra, Check the attached links,instruction and guides, 1st link will download pdf. showing how all panels are removed., Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Hummer H1 Service Manual Inner Kick Panels Replacement
Body Control Module Repairing Bad Solder Joints

Mar 31, 2016 | 2006 Hummer H3

1 Answer

How do i get to the drivers side HVAC blend actuator

You have to just about pull the whole dash out !

Removal Procedure

  1. Remove the front floor kick-up panel. Refer to Kick-Up Panel Replacement - Front Floor in Interior Trim.

  2. Remove the cover from the I/P electrical center.

  3. Remove the HVAC CON (HVAC controls) MiniFuse?® #27 from the I/P electrical center.

  4. Remove the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges and Console.

  5. Remove the instrument panel cluster (IPC) to steering column bracket retaining screws.

  6. Reposition the IPC to better access the LH temperature valve electric actuator.

Is yours manual or automatic HVAC system ? if you haven't done this before I suggest you take it to someone who has !

Jun 02, 2015 | 1999 Chevrolet Corvette

1 Answer

Remove kick panel


May 05, 2015 | Cars & Trucks

1 Answer

How do i remove a kick panel in a 1995 buick century ?

Kick switch is right on back of break pedal
meaning short of moving seat all way back and becoming a gymnast the brake switch should be easy to get too but there are 4 screws and 4 clips

now this where you have become gymnast two are on corners of follow bead line from steering wheel in both directions
once remove screws dont pry but gently test kick panel for play it should now slide in towards firewall and dismount

its a sensor on brake pedal there is easy adjust ment bolt before it sometimes bolts just get loose and find there way down

Jul 20, 2014 | 1995 Buick Century

1 Answer

Where is the fuel pump inertia switch on a 2004 excursion?

The fuel shutoff, or Inertia Switch, should be located behind the passenger side front kick panel.
LOOK on the right cowl panel right in front of the door and below the instrument panel. It is simply a button, that you push to reset, and get the fuel pump pumping fuel again.
see illustration.


also follow steps shown here
removing the passenger side front kick panel STEP1

removing the passenger side front kick panel STEP2

Push the switch to reset STEP3 70418098-7439-4d9c-a269-18f12c3751a5.jpg

May 17, 2014 | 2000 Ford Excursion

2 Answers

What does my ecu/ on my 1999 v-6 cougar look like

May 16, 2014 | 1999 Mercury Cougar

1 Answer

Where is my fuel pmp relay at

Hi Leeanne
If it is an injected model, here is the AllData instructions;

CIRCUIT OPENING RELAY (that is what it's called).

On Camry, Celica Corolla RWD and Van models, remove glove box. On Pickup and 4Runner models, remove right kick panel, glove box and speaker. On MR2 models, remove rear luggage compartment trim. On Cressida and 1985---Early 1986 Supra models, remove left kick panel. On Corolla FWD models, remove ECU cover from behind center console. On late 1986---1988 Supra models, remove right side kick panel.
Remove circuit opening relay with wiring from bracket.
Insert voltmeter positive probe into rear of connector at Fp terminal.
Meter should read battery voltage during cranking and while engine is running.
Disconnect electrical connector from relay and measure resistance between terminals.
If relay fails to perform satisfactory, relay is defective.

There is also a main relay on the left side. This will control the ECU

You might check this as well:

most of the time it is on the driver side down low inside the kick panel to test the pump you jump the two terminals under the hood by the fuse panel, the B+ one and the FP one with a paperclip

May 08, 2014 | 1985 Toyota Cressida

1 Answer

I cannot locate the broken audio amplifier in my recently obtained 1989 Bronco II. I don't want to disassemble the whole thing if I don't have to. Help?

It's behind the right front kick panel. Remove the trim peice from under the door, remove the kick panel screw, and pull out the kick panel, that last part will be a little tough but it can be done without taking off the roof trim.

May 23, 2010 | 1989 Ford Bronco II

1 Answer

How to remove kick panels on an '87 325

they are held in place by small philips head addition the drivers side kick panel has a 3 bolt enclosure that holds the hood release latch to the kick panel and left footwell, this must be removed as the fun must lift UP and OUT at the same time to release the lower lip of the kick panel which is tightly wedged.....finesse is required! by the way that a 5 1/4 speaker, but the footwell will also hold some 6 inch speakers as well....I have alpines in mine (89 cab)..put some Dynamat in while your down there!

Dec 29, 2008 | 1986 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides