Question about 1997 Ford Ranger SuperCab

Open Question

2.3L ford ranger ignition control module location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

manuelleiva
  • 97 Answers

SOURCE: where is the ignition module on 1994 ford ranger 2

on a ford is usually located on the side of the distributor or inside of it.i always find it on the outside of the distributor with a big electrical plug connected 2 it. hope this info helps. take care and good luck, manny

Posted on Feb 07, 2010

CARDERW
  • 1 Answer

SOURCE: looking for exact location ignition control module

WHERE IS THE INGITION CONTROL MODULE ON A 1995 FORD RANGER

Posted on Jun 18, 2011

emissionwiz
  • 75108 Answers

SOURCE: What is the specific ignition control module number for a 4-cylinder, 2.3 liter Ford Ranger?

I recommened only the factory part for this. You can buy it from most full service part stores and not just the Ford dealer. The part is
MOTORCRAFT Part # DY959 [ICM] (Ignition control module) $176.79
You can also mail order it from a site I use called rockauto.com the price given above is from that site.

Posted on Feb 19, 2012

Testimonial: "The information was good; however, after some exhaustive research (mostly thru Auto Zone), I found the ignition coil for a lot less $ at AdvanceAutoParts.com. It's not Motorcraft but it is OEM. Thanks for your response!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1006 ford ranger ignition cotrol module location


Your ranger doesn't have a ICM - ignition control module . PCM - engine computer controls spark .

Jan 16, 2017 | Ford Ranger Cars & Trucks

1 Answer

1989 ford ranger location of ignition control module


Check for a Thick Film Integrated (TFI) Module attached to the outside of the distrfibutor with about an 8 wire plug on it. That is Ford's ignition module. My recollection is the two screws attaching it to the distributor are odd-ball 7/32 in. size. If the module is taken off, use special ford di-electric grease on the base before re-attaching. For heat dissipation.

Nov 19, 2012 | 1989 Ford Ranger

1 Answer

What is the specific ignition control module number for a 4-cylinder, 2.3 liter Ford Ranger?


I recommened only the factory part for this. You can buy it from most full service part stores and not just the Ford dealer. The part is
MOTORCRAFT Part # DY959 [ICM] (Ignition control module) $176.79
You can also mail order it from a site I use called rockauto.com the price given above is from that site.

Feb 19, 2012 | 1992 Ford Ranger

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Where is the ignition module on 1994 ford ranger 2 3L


on a ford is usually located on the side of the distributor or inside of it.i always find it on the outside of the distributor with a big electrical plug connected 2 it. hope this info helps. take care and good luck, manny

Feb 07, 2010 | Ford Ranger Cars & Trucks

2 Answers

Where is the ignition control system located on a 1992 ford ranger?


the ignition module should be bolted to the side of the distributor. It takes a 5.5 millimeter socket or you can get a special tool at any good parts store. they should be able to check the module for you once you get it off.

Jan 16, 2010 | 1992 Ford Ranger

1 Answer

Where is the ignition control unit located?


The ignition control module on the Ford Ranger should be mounted either against the inner fender close to the radiator support, on the intake manifold, or on the distributor for some models that have a distributor ignition system. Hope this helped and best wishes.

Aug 02, 2009 | 1987 Ford Ranger

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1997 Ford Ranger SuperCab Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...