Question about Citroen Xsara

1 Answer

Al4 transmission problem - Xsara Citroen Cars & Trucks

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Citroen Master
  • 1,067 Answers

Need to replace or rebuild the transmission.

Posted on Jul 22, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The engine misfires


Take it back to the mechanic.

Feb 16, 2015 | 2008 Citroen C5 2.0

1 Answer

How do i check gearbox oil of citroen c3


AL4 oil cooler on a citroen C3 auomatic gearbox
25369447-bus3iqmg0jrasilho1abbg4j-4-0.jpeg

Jan 15, 2015 | Citroen Cars & Trucks

1 Answer

Al4 transmission gear fault 1st to 2nd


have you checked the fluid level as this is a symptom of low fluid , also get the OBD codes read as will tell you if a sensor/switch is faulty

May 14, 2014 | 2008 Peugeot 307cc 1.6

1 Answer

Where is the transmision dipstick on a 2002 peugeot 307


If it uses AL4 auto transmission, it's a dipstick with a black plastic handle. Look under battery tray or on the front part of the transmission.

Apr 25, 2014 | 2005 Peugeot 405

1 Answer

Citroen Xantia AUTO 2.0 alert lights cold (sport and snow lights)


The S light is also used like a 'check engine' light for auto transmission. There maybe some error in the transmission control system. You transmission has a computer that controls a lot of valves and solenoids in it. Check your transmission fluid level and it's integrity. If you have not changed the fluid for the last 50000kms then it's due for a change. Use only Peugeot recommended fluid. Other fluids will damage it. Mention your transmission type when buying. It's either AL4 or 4HP20. Best to buy it from authorized dealer. Garages that have a Lexia 3 scanner can scan for error codes for the transmission.

Aug 20, 2012 | 1998 Citroen Xantia

1 Answer

Tranmission ands four wheel drive locked out


For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 22, 2012 | 1998 Mitsubishi Montero Sport

1 Answer

How to remove a transmission for a 2002 GMC Yukon


Removal & Installation 4L60E/4L65E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
    • Plug the oil level indicator tube opening in the transmission.
    • Remove or disconnect the following:
    • Shift cable end from the transmission shift lever ball stud
    • If equipped with a transfer case, remove the front propeller shaft.
    • Rear propeller shaft.
  2. Plug the transmission oil cooler line connectors in the transmission case.
  3. Remove or disconnect the following:
    • Starter motor.
    • Transfer case, if equipped.
  4. Support the transmission with a transmission jack.
  5. Remove the transmission mount nuts.
  6. Remove the transmission crossmember.
  7. Remove or disconnect the following:
    • Torque converter access plug 4L60E/4L65E removal 9308kg37.gif

    • Flywheel to torque converter bolts
    • The two bolts securing the transmission rear mount to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • The stud and the bolt securing the transmission to the engine
    • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
    • The transmission from the vehicle
  8. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter.
    • Support the transmission with a transmission jack.
  2. Raise the transmission into place and remove the tool from the transmission.
  3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  4. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
    • Torque converter access plug.
    • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
  5. Remove the transmission jack from the transmission.
  6. Unplug the transmission oil cooler line connectors in the transmission case.
  7. Install or connect the following:
    • Starter
    • Transmission oil cooler lines to the transmission
    • If equipped with a transfer case, install the front propeller shaft.
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  8. Unplug the oil level indicator tube opening in the transmission.
  9. Install the transmission oil level indicator tube and seal to the transmission.
  10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  11. Lower the vehicle.
4L80E/4L85E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
  2. Plug the oil level indicator tube opening in the transmission.
  3. Remove or disconnect the following:
    • Shift cable from the transmission shift lever ball stud
    • If 4WD vehicle, remove the propeller shaft.
    • If RWD vehicle, remove the propeller shaft.
    • The transmission oil cooler lines from the transmission
  4. Plug the transmission oil cooler line connectors in the transmission case.
  5. Remove or disconnect the following:
    • Starter motor
  6. Support the transmission with a transmission jack.
  7. Remove or disconnect the following:
    • The two bolts securing the heat shield to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission
    • The two bolts securing the torque converter cover to the engine
    • The four bolts securing the torque converter cover to the transmission
    • The six flywheel to torque converter bolts
    • The two bolts and nut securing the transmission rear mount to the transmission
    • The stud and the bolt on the right side securing the transmission to the engine
    • The remaining six studs and the one bolt securing the transmission to the engine
    • Tool J21366 onto the transmission bell housing to retain the torque converter
    4L80E/4L85E removal 9308kg36.gif

  8. Pull the transmission straight back. Remove the transmission from the vehicle.
  9. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter
  2. Support the transmission with a transmission jack.
  3. Raise the transmission into place and remove the tool from the transmission.
  4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  5. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
    • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
    • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
    • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
    • The flywheel to torque converter bolts.
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
  6. Remove the transmission jack from the transmission.
  7. Install or connect the following:
    • Starter motor
  8. Unplug the transmission oil cooler line connectors in the transmission case.
  9. Connect the transmission oil cooler lines to the transmission.
  10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  11. Unplug the oil level indicator tube opening in the transmission.
  12. Install the transmission oil level indicator tube and seal to the transmission.
  13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  14. Lower the vehicle.
prev.gif next.gif

Oct 12, 2010 | 2002 GMC Yukon XL

1 Answer

Can I myself update the software? are the tools


unfortunatley no you cant, they are available due to block exempsion but itll probably cost more than the car is worth

Oct 20, 2009 | 2000 Renault 181

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...