Question about 1994 Dodge Viper

Open Question

Clutch bleeding - 1994 Dodge Viper

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?


a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




26351104-h2ljceqgvzc5xcxajl4olrsz-4-0.jpg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-1.jpeg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-3.jpg

Nov 11, 2016 | 2004 Ford Focus

1 Answer

How to bleed clutch cylinder for Nissan Sandra 2010


bleed clutch cylinder Robinny, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Bleeding clutch
Clutch bleed how to
Nissan Altima 2007 2012 Service Manual Clutch fluid On vehicle maintenance...
Help clutch bleeding Fail

Jul 19, 2016 | Nissan Cars & Trucks

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

How do i bleed clutch on fiat dublo


Clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Sep 11, 2012 | Fiat Doblo Cars & Trucks

1 Answer

I have an 84 Honda shadow vt700. The clutch was working but would slip when hot it would get to where I could release clutch with bike in 1st gear and nothing would happen! It would just continue to idle!...


Bleeding the hydraulics will not improve the friction drive of the clutch in any way,your clutch drive plate is worn out and needs replacing. To bleed the hydraulic line ,make sure that the master cylinder is fully topped up,pump clutch lever several times then tie ,using a zip tie the clutch lever all the way to the handle bar,gently open the bleed screw and await fluid to start dripping from the bleed screw, this may take an hour or two but it will eventually bleed itself,once 25% of the fluid has discharged from the the master cylinder tighten up the bleed screw and this is the easiest DIY way of bleeding a hydraulic system, without a pressure bleeder.

May 04, 2017 | Cars & Trucks

1 Answer

Where do you bleed the clutch at on a 1997 jeep wrangler what is the location of it


This all depends if this is a hydraulic clutch or if its cable operated, you can only bleed hydraulic clutches, to bleed it you would bleed at the ******, you will see the bleeder screw on the slave cylinder that operates the clutch fork.

Sep 03, 2011 | 1991 Jeep Wrangler

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

Not finding what you are looking for?
1994 Dodge Viper Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...