Question about Cars & Trucks

Open Question

I turn the ignition switch on and the car do not start.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If I have to turn my steering wheel or move it up and down for it to start whats my problem.


Sounds like a possible short inside the colum, I would check the ignition switch (key switch) if not that check the ignition switch from there check for a short in the steering colum.

Sep 13, 2012 | 2002 Cadillac Deville

1 Answer

Resetting the passlock


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Sep 08, 2012 | 2000 GMC Yukon Denali

1 Answer

Security light on car will not start can the alarm system fuse be pulled and this problem fixed?


NOPE WHEN CAR IN THEFT SECURITY MODE.YOU COULD HAVE WORN KEY OR WORN IGNITION SWITCH ALSO THE BCM COULD BE FAULTY. HAVE CAR CODE SCAN TO SEE WHAT THEFT CODE YOU ARE GETTING. YOU CAN GET CAR STARTED BY DOING THIS PROCEDURE.TURN THE IGNITION SWITCH TO ON POSITION FOR 10 MINUTES. WATCH SECURITY LIGHT WHEN IT VANISH OR TURN ITSELF OFF.TURN OFF IGNITION SWITCH WAIT 5 SECONDS START THE CAR.YOU HAVE TO TAKE CAR TO DEALERSHIP.IF THEY HAVE TO REPLACE THE KEYS AND IGNITION SWITCH ALSO BCM.THEY HAVE TO BE REPROGRAMMED WITH DIAGNOSTIC EQUIPMENT.

Feb 27, 2011 | 1999 Oldsmobile Alero

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

3 Answers

Reset immobiliser


u must put a key to ignition and open a drive door 3 times and press and hold lock button

Jan 18, 2010 | 2007 Ford F

2 Answers

Car was stolen ignition was ripped out of 2002 grandam, now car won't start with ignition and security light keeps flashing


groan.....gunna need a bit more info. but i'll try. What portion of the ignition was ripped out? The tumbler + switch? If so, you might need to get the car's system resent to recognize that it has a new ignition put in. Sime vehicles have a theft prevention system in place to prevent the vehicle from running if its been hot wired. Your best bet would be to replace the damaged ignition components (You did not mention if you did or not). If it still doesn't work after you have replced all of the ignition components. You can try to reset the vehicle (doesn't work on all) disconnect negative battery terminal and go back into vehicle and press down the brake pedal for about 30 seconds then reconnect battery and try it....good luck, hope this helps

Aug 17, 2009 | 2002 Pontiac Grand Am

2 Answers

Has truble starting and staying started


Sounds like a bad ignition switch. Not the lock cylinder, but the electrical switch.

Jun 30, 2009 | 1983 Buick LeSabre

1 Answer

Car ignition wont start or turn


Could be a bad lock cylinder or broken ignition switch (under the dash on top of the steering column). If you disconnect the switch from the control rod that comes from the cylinder and the cylinder turns you need a new switch.

Jun 17, 2009 | 2002 Cadillac Deville

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

2 Answers

1999 Olds ignition switch problems


Hi....
In your Intrigue to use the New Passcode sensor .
You need to program the new Passcode to the ECM. of the Vehicle.
This is a prosses that involve around 30 minutes maybe a little more.

Remove the old Ignition switch.
Install the new Ignition switch. with the new Passlock sensor.
Turn the key to on position and try to start a few senconds. them leave the key on run position.
For 10 minutes and NOT more than 11 minutes.
Them turn the key to OFF position for exactly 30 seconds.
Them turn the key to Run position 10 minutes or 11.
them turn back the key to OFF position for 30 seconds.
Them turn the key to Run position 10 minutes or 11,
Turn the key to OFF position and wait 1 minute, them try to start the vehicle.
If the car start you are DONE.
But if Not Letme know to give you more information.

OK I hope this help to try solve your problem.

Thank you for use fixya...

Nov 15, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...