Question about Cars & Trucks

1 Answer

Pt cruiser troubleshooting

My Pt cruiser does not have power going to the fuses for asd. what is the problem?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What would case for a 2006 pt cruiser when you grt to 2000 rpm it spits and putter and bogs down

Posted on Mar 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

  • 290 Answers

SOURCE: chrysler pt cruiser fuel filter location?

Under vehicle, center, below seating area, mounted on top of fuel tank, in fuel pump module

Posted on Mar 27, 2009

localwonder
  • 6784 Answers

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.


9c06de2.jpg

Posted on Apr 30, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of powertrain control module on 01 PT Cruiser?

The PCM attaches to a bracket welded on the dash panel

2d254d5.gif

Posted on Oct 31, 2009

BCAS1298
  • 3092 Answers

SOURCE: replacing a starter in a PT. Cruiser 2001

Remove battery and battery support you'll be able to undo starter bolt's trough there and slip starter out.

Posted on Dec 08, 2009

Testimonial: "This didn't help, because you had to remove the engine structural collar under the starter to get at the starter bolt. It was more complicated."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 pt cruiser keeps blowing fuel pump fuse,replaced fuel pump, no change.runs rough at idle and stalls,blows fp fuse,also replaced ign.coil,plug wires and plugs also changed relays


There are two fuses for the fuel pump relay. One fuse is load side of relay, that fuse also sends voltage to load side of asd relay, the asd relay sends voltage to several systems, two of which are the fuel injectors and ignition coil. I'm not telling you to replace, anything, but, you need to do some testing.
The other fuse goes to control side of relay, smaller amp fuse. I don't know the amp rating of the fuse that keeps blowing.
See that fuse, it supplies voltage to load side of fuel pump relay and also to asd relay.
26322929-c15bjyrfwzlf33vqjpu1ik1c-2-0.jpg

Oct 22, 2016 | 2004 Chrysler PT Cruiser

2 Answers

I just replaced a fuel pump in a 2008 pt cruiser. Getting good power to the pump. Asd relay is good. Wiring is good. Still won't pump fuel. Thoughts?


Check to see if there is a fuse for the fuel pump, then check if there is a impact shut off switch like the fords, and sometimes the fuel pump will run till after the ignition is cranked over....

Nov 08, 2014 | 2008 Chrysler Pt Cruiser

1 Answer

I have an 04 PT cruiser turbo. Starter was bad so I replaced it and new starter repeats problem. After many check, engine will not crank. Batery tested and charged as good. Starter does not engage unless...


I saw something on another site. and it was doing the same thing you have said and it turned out to be the ignition module the electrics on the ignition. remove it off the ignition and open it up and check that the solid parts. some suffer from dry joints. 81036c61-543f-4d51-8488-531140cad9d9.jpg

Aug 22, 2013 | 2004 Chrysler PT Cruiser

3 Answers

My 2005 PT Cruiser keeps blowing fuse 13, what is the problem


Fuse number 13 is a 20amp fuse that powers the ASD relay and the computer among other things.
Someone will have to pull the relay and check the circuits one by one to find the short. It could be any one of a dozen or more components.

Aug 09, 2012 | 2005 Chrysler PT Cruiser

1 Answer

Coil want spark on pt cruiser


When you have no spark at the coil,Then coil needs power from ignition which is supplied by the ASD relay,you also need a ground signal this is from the PCM,which recieves its input from the cranksensor, which is located,under the starter,Check for open fuses especially ignition fuse, and make sure the harness to the crank sensor is good,

Mar 30, 2012 | 2003 Chrysler PT Cruiser

1 Answer

2005 pt cruiser won't start won't crank, everything works


When you turn the key on the ASD relay should turn on the fuel pump and power the injector, Do this lets cheat the system go to the ASD rely open the cover expose the inside have some one turn the key on does the ASD make contact? If not turn the key on collpase the ASD so it make contact do you hear the fuel pump come on? Now try this just as how you iopen the ASD do the same to the starter relay. Put the car in gear e brake on someone in the vehicle in case the car start and you are in front of it and it runs you over so at least they step on the brakes. Key on ASD exposed as your collapse the starter relay does the ASD relay turn on? Here why if you can control all the relay from under the hood you will need a ignition switch (the eletrical part)

Feb 22, 2012 | 2005 Chrysler PT Cruiser

3 Answers

I need a fuse box diagram for a 2002 chrysler pt cruiser limited edition


I am sorry but our diagrams only go back as far as the 2004 model year. I suggest you try eBay for a used owners manual.

Feb 20, 2012 | 2002 Chrysler PT Cruiser

1 Answer

My 2005 PT Cruiser shows error codes P0508, P0688, and P0522. Sometimes it runs well, and other times it runs rough then dies and won't start back.


this obd2 trouble code table can help u understand the meaning of code.
po522, the possible solution:
The most likely cause is a faulty oil pressure sensor/switch.
for p0688, you can Check all the ECM fuses, if the fuses are OK try replacing the ASD relay.

Aug 15, 2011 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...