Question about 2007 Pontiac Solstice Convertible

Open Question

Starter vehicle remove - 2007 Pontiac Solstice Convertible

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing the starter on a 2008 Saturn Vue XE 2.4L


Starter Motor Replacement (LE5 2.4L and LAT-2.4L)

Removal Procedure

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection (With LAT-2.4L) ( See: Vehicle Lifting > Procedures > Lifting and Jacking the Vehicle) .

Zoom and Print Options
3. Disconnect the starter motor electrical connector (3).
4. Remove the starter solenoid BAT terminal nut (4).
5. Remove the battery positive cable terminal (1) and engine harness terminal (2) from the starter motor.

Zoom and Print Options
6. Remove the starter motor bolts.
7. Remove the starter motor from the vehicle.



Installation Procedure

1. Position the starter motor to the vehicle.

Zoom and Print Options

Notice: Refer to Fastener Notice ( See: Vehicle > Vehicle Damage Warnings > Fastener Notice) .


Important: Hand tighten all bolts before finalizing any torques.


2. Install the starter motor bolts.

Tighten the bolts to 43 N.m (32 lb ft).


Zoom and Print Options
3. Install the engine harness terminal (2) and the battery positive cable terminal (1) to the starter motor. Ensure that the battery positive cable terminal anti-rotation feature is aligned correctly.
4. Install the starter solenoid BAT terminal nut (4).

Tighten the nut to 15 N.m (11 lb ft).

5. Connect the starter motor electrical connector (3).

image-5snr4wklzrtsarf5gbfkw1ee-3-0.gif

image-5snr4wklzrtsarf5gbfkw1ee-3-2.gif

image-5snr4wklzrtsarf5gbfkw1ee-3-5.gif

Jul 08, 2017 | Saturn Cars & Trucks

1 Answer

How do you change starter on a 2005 ford freestyle?


Removal & Installation

Specific to:
Ford Freestar 2004-2006
Mercury Monterey 2004-2006
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.
To install:
Fig. Starter motor mounting-3.9L and 4.2L engines
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 21 ft. lbs. (28 Nm).
  3. Connect the starter electrical harness.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
GET 35 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS

Jan 20, 2016 | Ford Cars & Trucks

1 Answer

How to remove and install starter motor on 2000 malibu location of mounting bolts


REMOVAL & INSTALLATION 2.4L Engine
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Position a drain pan under the oil filter, then remove the oil filter.
  4. Remove the top starter bolt.
  5. Raise and safely support the vehicle.
  6. Remove the lower starter retaining bolt.
  7. If necessary, position the engine wiring harness aside.
  8. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  9. Remove the starter from the vehicle. To install:
  10. Raise the starter to the vehicle, then attach the wiring.
  11. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm). Fig. 1: When installing the starter on the 2.4L engine, tighten the mounting bolts to 66 ft. lbs. (90 Nm) 87952040.gif

  12. If moved, reposition the engine wiring harness.
  13. Attach the solenoid electrical connectors.
  14. Carefully lower the vehicle.
  15. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  16. Replace the oil filter.
  17. Fasten the air inlet duct to the throttle body.
  18. Connect the negative battery cable.
  19. Check the oil level and add if necessary.
  20. Start the engine, recheck the oil level and add if necessary.
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Remove the lower closeout panel.
  4. Remove the electrical leads. Fig. 2: Two electrical leads connect to the starter solenoid. The larger one has battery power as long as the battery is connected. The smaller one only has power when the key is turned to START 93202p09.jpg

  5. Remove the starter motor to engine bolts, then remove the starter from the vehicle. To install:
  6. Install the starter. Position one engine-to-starter bolt in the lower bolt hole, then finger-start the bolt.
  7. Connect the electrical leads to the starter. Tighten the cable to the solenoid to 106 inch lbs. (12 Nm).
  8. Install the starter-to-engine bolts and tighten to 37 ft. lbs. (50 Nm)
  9. Install the lower closeout panel.
  10. Lower the vehicle.
  11. Connect the negative battery cable.
prev.gif next.gif

Jan 21, 2011 | 2001 Chevrolet Malibu

1 Answer

Starter diagram for a 1994 dodge intrepid


3.3L Engine
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Fig. 1: Disconnect the negative battery cable 88172g31.gif

  2. Remove the three bolts attaching the starter to the engine/transaxle. Fig. 2: Remove the three starter mounting bolts 88172g32.gif
    CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
  4. Remove the battery positive cable nut from the starter and remove the cable. Fig. 3: Remove the battery positive cable nut from the starter and remove the cable 88172g33.gif

  5. Disconnect the push on solenoid connector.
  6. Remove the starter from the vehicle. To install:
  7. Clean all wire terminals of dirt, grease or corrosion.
  8. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  10. Lower the vehicle.
  11. Connect the negative (-) battery cable.
3.5L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. For easier servicing, do not remove the wiring from the starter motor at this time.
  4. Remove the three bolts attaching the starter to the engine. Fig. 4: Remove the three bolts attaching the starter to the engine 88172g34.gif

  5. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
  6. Remove the battery positive cable nut from starter and remove the cable.
  7. Disconnect the push on solenoid connector.
  8. Remove the starter from the vehicle. To install:
  9. Clean all wire terminals of dirt, grease or corrosion.
  10. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  11. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  12. Lower the vehicle.
  13. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Tools needed to remove starter on 94 dodge spirit 3.0 liter V6


Regular socket wrench set, wrench set, screwdriver, etc.: REMOVAL & INSTALLATION Fig. 1: These three attaching bolts hold the starter motor to the engine/transaxle assembly - all models 86722051.gif
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Remove the engine undercovers, if so equipped.
  2. Remove the 3 bolts attaching the starter to the engine/transaxle. CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the heat shield and its clamp, if so equipped.
  4. Remove the two electrical wire connector terminal nuts and remove the wiring connector from the starter.
  5. Remove the starter from the vehicle. To install:
  6. Clean all wire terminals of dirt, grease or corrosion.
  7. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 80 inch lbs. (9 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  8. Install the heat shield if one was removed.
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm) for all vehicles except Premier and Monaco. Tighten the attaching bolts to 20 ft. lbs. (27 Nm) for Premier and Monaco.
  10. Install any undercovers which were removed from the vehicle.
  11. Lower the vehicle.
  12. Connect the negative (-) battery cable. Fig. 2: After disconnecting the starter's electrical wiring, remove the 3 mounting bolts . . . 86722p15.jpg
    Fig. 3: . . . then the starter motor can be lowered from the underside of the vehicle 86722p16.jpg
prev.gif next.gif

Sep 24, 2010 | 1991 Dodge Spirit

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

I need to fix a starter on my car


3.1L Engine
Besides regular hand tools, a special oil pressure sensor socket will be necessary to complete this operation.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the A/C compressor brace (if equipped).
  4. Extract the wiring harness from the retainer and position it out of the way.
  5. Remove the cover from the starter wiring.
  6. Remove the outer nut and disengage the wiring from the starter solenoid.
  7. Disconnect the electrical connector from the oil pressure gauge sensor.
  8. Using the special socket, remove the oil pressure gauge sensor.
  9. Unbolt the starter from the engine. Retain any shims.
To install:
  1. Install the starter to the engine, reuse any shims that were removed. Tighten to 32 ft. lbs. (43 Nm).
  2. Connect the wiring to the solenoid and install the outer nut.
  3. Place the cover over the starter wiring.
  4. Replace the oil pressure gauge sensor using the special socket.
  5. Plug the electrical connector onto the sensor.
  6. Mount the harness to the retainer.
  7. Install the A/C compressor brace (if equipped).
  8. Lower the vehicle.
  9. Connect the negative battery cable.

3.4L Engine
This starter is serviced only as a complete unit.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Disconnect the electrical connectors at the starter.
  4. Remove the converter cover.
  5. Remove the starter motor mounting bolts, and remove the starter.

To install:
  1. Install the starter motor to the engine using the mounting bolts. Torque the bolts to 35 ft. lbs. (47 Nm).
  2. Install the converter cover.
  3. Reconnect the electrical connections to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

3.8L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the cover from the starter wiring.
  4. Remove the outer nut and wiring from the starter solenoid.
  5. Remove the screws retaining the wiring harness clips and position the harness out of the way.
  6. Take out the screw that retains the plastic flywheel cover and remove the cover from the vehicle.
  7. Remove the bolts retaining the starter to the engine block, and remove the starter from the vehicle.

To install
  1. Install the starter and tighten the bolts to 32 ft. lbs. (43 Nm).
  2. Install the plastic flywheel cover and screw
  3. Reposition the wiring harness, and screw in the retaining harness clips.
  1. Reconnect the wiring to the solenoid and install the outer nut.
  2. Replace the cover over the starter wiring.
  3. Lower the vehicle.
  4. Connect the negative battery cable.

Jan 19, 2010 | 1994 Pontiac Trans Sport

1 Answer

Replacing a new starter on a 93 isuzu rodeo


Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--

8e64f3e.gif
4-cylinder engine starter connections



  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
  4. Tag and disconnect the starter battery and control wiring at the starter.
  5. If equipped, remove the starter bracket and/or heat shield.
  6. Remove the starter-to-engine bolts.
  7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
To install:
  1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
  2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  3. Install the starter bracket and/or heat shield, if equipped.
  4. Connect the battery and starter control electrical wires to the starter.
  5. If the EGR pipe was removed, install it.
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Start the vehicle to make sure the starter functions correctly.
This is for the V6 motor--

8fdc27b.gif
6-cylinder engine starter installation


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Label and disconnect the battery and starter control wires from the starter.
  4. If equipped, remove the starter bracket and/or heat shield.
  5. Remove the starter-to-engine mounting bolts.
  6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
To install:
  1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  2. Install the starter bracket and/or heat shield, if equipped.
  3. Reconnect the electrical connectors to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
  6. Start the vehicle to make sure the starter functions correctly.

Nov 19, 2009 | 1993 Isuzu Rodeo

1 Answer

Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


Starter - Removal & installing
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.
020fef8.jpg

Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

98933b2.jpg

Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

e2afde4.jpg

Remove the starter motor from the vehicle


The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 1998 Dodge Grand Caravan

1 Answer

Replace an alternator on a 2005 chevy venture (instructions)


REMOVAL PROCEDURE

IMPORTANT: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.

  1. Disconnect the battery ground (negative) cable from the battery.
  2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.
  3. Remove radiator air baffle assembly.
  4. Remove the starter motor BAT terminal nut and electrical leads.
  5. Remove the starter motor S terminal nut and electrical lead.
  6. Remove the torque converter co
  7. Remove the starter motor bolts.
  8. Remove the starter motor.
INSTALLATION PROCEDURE
  1. Install the starter motor.
  2. Install the starter motor bolts. Tighten the starter motor bolts to 47 N.m (35 lb ft)
  3. Install the torque converter cover.
  4. Install the starter motor S terminal electrical lead and nut. Tighten the starter motor solenoid S terminal nut to 3 N.m (27 lb in).
  5. Install the starter motor BAT terminal electrical leads and nut. Tighten the starter motor solenoid BAT terminal nut to 10 N.m (89 lb in) .
  6. Install radiator air baffle assembly.
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery.

Jul 25, 2009 | 2005 Chevrolet Venture

Not finding what you are looking for?
2007 Pontiac Solstice Convertible Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...