Question about Cars & Trucks

1 Answer

Ford problems i need a dual mass flywheel and clutch kit for a ford mondeo 2009 2.2 titanium x sport 6 speed hatchback i cant find one for sale anywhere

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Http://www.ebay.com/itm/BRAND-NEW-SOLID-FLYWHEEL-GENUINE-FORD-CLUTCH-CSC-FORD-MONDEO-2000-2007-2-2-D-/321233915244?pt=Motors_Car_Truck_Parts_Accessories&hash=item4acb088d6c&vxp=mtr

Posted on Jan 03, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 184 Answers

SOURCE: mondeo clutch problem

yes it will fit.

Posted on Mar 18, 2009

  • 82 Answers

SOURCE: 1989 vette L98 external balance eng. w/6 speed ZF

The clutch disk and pressure plate should be balanced and can be mounted in any position that the mounting holes line up. If there is a hole for an alignment dowl, then it is recommended to do so. otherwise it doesnt matter.

The internal balancing is taken care of by the flywheel only.

Posted on Sep 15, 2009

  • 2187 Answers

SOURCE: I replaced the clutch assy. in a 2003 santa fe 2wd

Check if there is air in the system. You need to bleed out the clutch. Inspect the pedal linkages for binding or anything out of the ordinary. If bleeding the clutch did not resolve the issue, you need to go back to the transmission and inspect the fork or pivot ball. It could be possible that the conversion kit did not match the model that you have. It is possible that bad seals causing debris may have caused the issue and it was just coincidence that after replacing the flywheel did this happen.

You may also need to replace transmission fluid.

Posted on May 12, 2011

jgwhomeequip
  • 1902 Answers

SOURCE: Renault traffic 6 speed 53

Sounds like the throwout bearing is going bad. Which is telling you that it might be time for a new clutch kit in your vehicle

Posted on Jun 26, 2011

  • 98 Answers

SOURCE: ive got ford mondeo tdci 54 plate.. ive just had the dual mass flywheel replaced but now the clutch is playing up it goes stiff and wont go into gear, could this be it needs clutch fluid??

Angela, I'll be honest I'm confused. It shows "problem with Toytoa Celica" but you mention a Ford Mondeo in your post. Just to be sure we're talking about a Ford Mondeo that had the flywheel replaced, correct? Chances are if they replaced the flywheel you normally would always replace the clutch disk with it. If this is a hydraulic clutch system you don't typically have to open the hydraulic system to swap out the flywheel and clutch on a car. This would lead me to believe clutch fluid isn't your answer, but I would at least make sure you check it. If they DID have to open the system the clutch needs to have the air bled out of the hydraulic lines.

Posted on Nov 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi guys I have d22 a 1991 navara 5 speed manual,diesel.its making a squeling noise when using clutch now just sometimes in wont go into 4th gear its like neutral,,,any ideas whats going on,,,cheers


the sound is maybe coming from the release bearing on its way out.
The gear selection issue can be the pressure plate.
i would check the clutch hydraulics first if thats okay.
next check transmission oil level and condition
if that checks out replace the clutch kit
being a diesel it will have a dual mass flywheel those cannot be reconditioned must be replace

Sep 06, 2016 | Nissan Navara Cars & Trucks

1 Answer

Ive got ford mondeo tdci 54 plate.. ive just had the dual mass flywheel replaced but now the clutch is playing up it goes stiff and wont go into gear, could this be it needs clutch fluid??


Angela, I'll be honest I'm confused. It shows "problem with Toytoa Celica" but you mention a Ford Mondeo in your post. Just to be sure we're talking about a Ford Mondeo that had the flywheel replaced, correct? Chances are if they replaced the flywheel you normally would always replace the clutch disk with it. If this is a hydraulic clutch system you don't typically have to open the hydraulic system to swap out the flywheel and clutch on a car. This would lead me to believe clutch fluid isn't your answer, but I would at least make sure you check it. If they DID have to open the system the clutch needs to have the air bled out of the hydraulic lines.

Nov 24, 2012 | 2002 Toyota Celica

1 Answer

Grinding in tranny after replacing clutch


Did you remember to torque all of your clutch plate bolts? Flywheel bolts?

May 04, 2010 | 1996 Ford F250 Crew Cab

2 Answers

Dual mass fly wheel


did u git the timin rite-now the flywheel fits as replacement correct-do u hav a repair manual!

Aug 16, 2009 | Ford Focus Cars & Trucks

1 Answer

1989 vette L98 external balance eng. w/6 speed ZF trans. installed new LUK (GM) dual mass flywheel w/ OEM replacement clutch/pressure plate assy. - eng. is out of balance. what is proper allignment for...


The clutch disk and pressure plate should be balanced and can be mounted in any position that the mounting holes line up. If there is a hole for an alignment dowl, then it is recommended to do so. otherwise it doesnt matter.

The internal balancing is taken care of by the flywheel only.

Jul 10, 2009 | 1989 Chevrolet Corvette

2 Answers

96 FORD F-350 7.3 TURBO DIESEL 5 SPEED


no, it shouldnt have any looseness to it and dual mass flywheels are VERY expensive to replace, BUT yes it can be converted to a solid flywheel, check out autozone.com part number MU1989 or advanceautoparts.com part number 798, that should get you on the right path to curing your problems, i welded the two independantly turning discs of my dual mass flywheel together but i wouldnt recommend anyone doing that without the proper equipment to do so (i.e. precision lathes, cast iron welding rods, etc)

Mar 29, 2009 | 1996 Ford F350 Crew Cab

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...