Question about 2005 Ford Five Hundred

1 Answer

I need keypad entry code to 05 ford five hundred

Posted by on

  • I aint no mechanic
    I aint no mechanic Sep 04, 2017

    One can find the keypad entry code located on the back of the fuse box that is located inside by the brake. It is a pain to get to, but if determined should take between 15-30 min. There is a youtube video showing somewhat how to do it. After removing the three screws holding it on, use your cell phone video to capture the five numbers.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine was on a little card in the flap of my owners manual.. I purchased my car 10 months ago and it was in there when I was thumbing thru the manual

Posted on Jan 05, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 154 Answers

SOURCE: Cold cranking amps - 05 Ford Five Hundred

You can buy a battery with as many cca as you like as long as the battery fits your battery box. The cca is how long you can crank motor befor you run out of power If you can get a 700-750 cca battery you will be fine. But you could do with a 450-500cca battery if you want. But I wouldn't go less than that especially if your running the v8

Posted on Jul 25, 2008

  • 2 Answers

SOURCE: 2006 Ford Five Hundred -- Where's the fuel filter?

right rear just in front of wheel. push clips back and remove old filter. apply new filter insuring flow is correct direction by arrow on filter press the clips back in place and you are ready. check to see if it is leaking.

Posted on Mar 16, 2009

  • 1 Answer

SOURCE: 05 ford five hundred reset fuel shut off switch

i have a 2005 ford 500 and my fuel reset switch is on the passanger side under the glove box to the right. it is labaled. hope this helps

Posted on Apr 07, 2009

  • 93 Answers

SOURCE: how to reset factory code on keyless entry ford five hundred

if you do not already know the factory code, the only way it can be obtained is by your local ford dealer. the proprietary computer equiptment they have can access the code that is programed in vehicles security module. if you purchased it used..it is often that the keyless entry code id card is still withe the owners manual..it is a 5 digit code printed on an credit card sized card that is white in color..i hope this helps you...good luck

Posted on Jun 09, 2009

  • 56 Answers

SOURCE: 05 Ford Five Hundred won't start because

You will have to call the dealer and they will have to call the factory.

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford keyless entry key pad needs to be disabled


Google the programming instruction for the key pad and reprogram the system to the code of your choosing

Nov 06, 2013 | 2005 Ford Five Hundred

1 Answer

What is the procedure for programming the key pad on the door to unlock the car?


  1. Locate the permanent factory remote keyless entry code in your car's owner's manual or by contacting the dealership.
  2. Enter the factory code on the keypad and press the "1/2" button on the keypad within five seconds to start the programming sequence.
  3. Enter a new five-digit code into the keypad within five seconds.
  4. Wait for the locks to cycle once to confirm the new code was successfully programmed.

Feb 24, 2011 | 1995 Ford Taurus

1 Answer

Ware do I find the keypad numbers to reset it on a 2006 fivehundred?


The car came with a card that has this information printed on it. Regardless of personal settings on the remote entry keypad, this code will always work. It should look like a credit card and (hopefully) is in the glovebox w/ your owner's manual. If not, your Ford dealer is your next stop.

Good luck.

Jan 15, 2011 | 2006 Ford Five Hundred

1 Answer

I need to get a spare key for my 2005 ford 500


Unfortunately you will need to goto your local ford dealer and they will have to cut you a new key and reprogram the new key and possibly your old key unless it is definitively the master key. It is a worthwhile expense and if you have a keyless entry keypad and do not know the code they can also give that to you then since they will be in the computer. Hope this helps.

Aug 07, 2010 | 2005 Ford Five Hundred

1 Answer

How do I change the code for key less entery on the key pad on door


Programming a personal entry code The factory set code cannot be reprogrammed but you can create your own 5 digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Up to three personal entry codes may be programmed to the vehicle. To create your own personal entry code:

  • 1. Enter the factory set code.
  • 2. Within five seconds press the 1-2 on the keypad.
  • 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.
  • 4. Press 1-2, 3-4 or 5-6 to indicate which of the three personal entry code positions you wish to use.
  • 5. The doors will again lock then unlock to confirm that your personal key code has been programmed to the module.
Tips:

  • Do not set a code that uses five of the same number.
  • Do not use five numbers in sequential order.
  • The factory set code will work even if you have set your own personal code.
  • If you program a code to a position that already contains a set code, the previously-set code will be erased.

Erasing personal code
  • 1. Enter the factory set 5 digit code.
  • 2. Within five seconds, press the 1-2 on the keypad and release.
  • 3. Press and hold the 1- 2 for two seconds. This must be done within five seconds of completing Step 2.
All personal codes are now erased and only the factory set 5 digit code will work.

Good luck (remember commend and rated this).

May 03, 2010 | 1996 Ford Explorer

2 Answers

How do i reprogram keyless entry codes


door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:
  1. Enter the factory set five-digit code (the keypad will illuminate when pressed).
  1. Press 1/2 within five seconds of Step 1.
  1. Enter the unique five-digit code.
The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:
  1. Enter factory set five-digit code.
  1. Press 1/2 within five seconds of Step 1.
  1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.
The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:
  • one minute of keypad inactivity
  • the keyless entry remote transmitter UNLOCK button is pressed
  • the ignition is turned to the ON position.
Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

Dec 01, 2009 | 2004 Ford F350

2 Answers

How to reset factory code on keyless entry ford five hundred


if you do not already know the factory code, the only way it can be obtained is by your local ford dealer. the proprietary computer equiptment they have can access the code that is programed in vehicles security module. if you purchased it used..it is often that the keyless entry code id card is still withe the owners manual..it is a 5 digit code printed on an credit card sized card that is white in color..i hope this helps you...good luck

Jun 07, 2009 | 2005 Ford Five Hundred

1 Answer

Need factory code for keyless entry pad


To locate the original keypad code, open the passenger/rear door. Pull the on-body rubber weatherstrip out, around the rear side of the door closure. Fold the right/rear seatback down into the locked position to facilitate access to the right/rear seat belt anchor. Carefully pry the upper plastic panel that houses the height adjuster and seat belt anchor off the body taking care not to damage the panel. Now pry the lower panel outward just far enough to enable access to the Vehicle Security Module, where you'll see three electrical connectors plugged into it, coloured green, grey, and blue. On the module will be a series of digits on a label similar to 5L2T-15K602-EA. Beside those digits are five numbers. Those five numbers are the keyless entry keypad code.

Apr 22, 2009 | 2005 Ford Explorer

1 Answer

Keyless entry on door 2003 ford f-150


this is from the Ford owners manual.
Programming a personal entry code
To create your own personal entry code:
1. Enter the factory set code.
2. Within five seconds press the 1 • 2 on the keypad.
3. Enter your personal 5-digit code. Each number must be entered
within five seconds of each other.
4. The doors will again lock then unlock to confirm that your personal
keycode has been programmed to the module.
Tips:
• Do not set a code that uses five of the same number.
• Do not use five numbers in sequential order.
• The factory set code will work even if you have set your own personal
code.
• If you set a second personal code it will erase your first personal code.

Mar 30, 2009 | 2003 Ford F150 Regular Cab

2 Answers

How do i change touchpad code on 2007 edge?


Programming a personal entry code and keypad association to
memory seats and mirrors (if equipped)
To create your own personal entry code:
1. Enter the factory set code.
2. Within five seconds press the 1 • 2 on the keypad.
3. Enter your personal 5-digit code. Each number must be entered
within five seconds of each other.
4. To associate the entry code with a memory setting, enter a sixth digit
to indicate which driver should be set in a memory recalled by the
personal entry code:
• Pressing 1 • 2 recalls Driver 1 settings.
• Pressing 3 • 4 recalls Driver 2 settings.
• Pressing other keypad buttons or not pressing a keypad button as a
sixth digit does not set a driver and will not recall a memory setting.
Note: The factory-set code cannot be associated with a memory
setting.
5. The doors will lock then unlock to confirm that your personal keycode
has been programmed to the module.
Tips:
• Do not set a code that uses five of the same number.
• Do not use five numbers in sequential order.
• The factory set code will work even if you have set your own personal
code.
Erasing personal code
1. Enter the factory set 5–digit code.
2. Within five seconds, press the 1 • 2 on the keypad and release.
3. Press and hold the 1 • 2 for two seconds. This must be done within
five seconds of completing Step 2.
All personal codes are now erased and only the factory set 5–digit code
will work

Oct 10, 2008 | 2007 Ford Edge SEL Plus

Not finding what you are looking for?
2005 Ford Five Hundred Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...