Question about 1999 Honda Prelude

1 Answer

Blower motor removal

How do you remove a blower motor in a 1999 Honda prelude once it is loose

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Its in the FSM, its non trivial
1999 is, gen5 . read your FSM here, its in the HVAC sections
or at alldata.com

#5 be it. 97-01
http://hondatech.info/downloads/Auto/Manuals/Prelude/

Posted on Jan 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ne1cthat
  • 1 Answer

SOURCE: 1989 honda prelude

if you are somewhat mechanically inclined you should be able to follow these steps in order I put them. #1 Disconnect the negative battery terminal.#2 Disconnect the electrical terminals from the alternator.#3 Loosen the alternator adjustment and pivot bolts and remove the belt.#4 Remove the bolts and separate the alternator from the engine.#5 Remove the alternator bracket from engine.#6 Remove the fuel filter and any of the vacuum lines in the way.#7 Remove alternator from top of the car.#8 Installation is reverse of removal.

Posted on Aug 06, 2008

dustyboner
  • 331 Answers

SOURCE: I'm trying to remove the

30e64e8.png
f38da4e.png
3f0119e.png
e3b3113.png
84eb4bd.png
a932a1b.png

4. Install in the reverse order of removal, and make sure there are no air leaks.

Posted on Dec 31, 2008

jjjhandyman
  • 145 Answers

SOURCE: Honda Civic heater / blower noise.

you need to remove your glove box assy.(beleave only 2 screws and pivot clips) make sure its not anything from glove box that has slipped behind. once box is out uf way you can access easier the blower motor assy. it actually attaches into blower box from bottom side. when looking at you will find three screw/bolts fastening motor to casing. remove those and then slowly lower motor and fan cage(attached to motor shaft) out from housing. sometimes it takes a little convincing to come out but not real tough. once out you most likely find the object causing noise in fan cage or resting up on lip area of housing unit. once found install in reverse order. let me know if this helps or if we need to dig a little deeper into! good luck!
joel

Posted on Feb 02, 2009

  • 432 Answers

SOURCE: i have 1991 honda accord, heater blower motor does

If you have removed the blower motor, Connect it to a 12 volt power supply(your battery)with some jumper wires.It should turn fast, be careful when you connect it, have a good grip on it, it will jump just a little. If it dont run fast its junk. The other 2 things
1)The fan switch
2) The resistor that slows the fan at low speeds.

Posted on Jun 27, 2009

  • 496 Answers

SOURCE: honda pilot blower motor stops

Hi,
When you removed your motor, did you check in the area where the motor mounted to see if there was an obstruction? It could be a bit of insulation or paper... just a thought.
Good luck!

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda civic 2003 heater fan not working


The blower is located under the passenger side of the dash. There is likely a trim panel that will need to be removed to gain access to the blower motor. Once the panel is out of the way the three screws that hold the blower to the housing can be removed and the blower motor will drop out. You can then inspect and/or remove the parts that are blocking it.

Nov 06, 2012 | 2003 Honda Civic

1 Answer

My 1999 honda prelude sh the oil leak from mount of the filter between the block and the parts with two hose connected where the oil filter screw i need a break away diagram how to remove or diassemble


We do not have this diagram. The info is contained in the factory service manual and that is copyrighted and not free to share on the web. Sorry. I am told you can access the info for a small fee here: alldatadiy.com

Apr 08, 2012 | 1999 Honda Prelude

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

98 Chev astro - no blower need to trace wiring also wiper motors


Check fuses. Also plug and unplug electrical connections...I lost blower once...had it removed and decided to test it with another 12VDC supply and it worked fine. Checked for power at plug and it was good too. Replugged it and motor worked....it was simply a bad plug connection...either loose and/or dirty. 2 years later it's still working fine!

Oct 28, 2009 | 1999 Chevrolet Astro

2 Answers

Honda Civic heater / blower noise.


you need to remove your glove box assy.(beleave only 2 screws and pivot clips) make sure its not anything from glove box that has slipped behind. once box is out uf way you can access easier the blower motor assy. it actually attaches into blower box from bottom side. when looking at you will find three screw/bolts fastening motor to casing. remove those and then slowly lower motor and fan cage(attached to motor shaft) out from housing. sometimes it takes a little convincing to come out but not real tough. once out you most likely find the object causing noise in fan cage or resting up on lip area of housing unit. once found install in reverse order. let me know if this helps or if we need to dig a little deeper into! good luck!
joel

Feb 02, 2009 | 1999 Honda Civic

2 Answers

Still Can't Find Heater/Blower Fuse in 85 Honda Prelude?


Found this wiring diagram. Don't know if it is accurate? My wiring diagrams on your model year isn't very good. Voltage to blower motor goes hot with key on and is fused. The control for blower motor is on the ground circuit, bottom wire at blower motor.
blower motor-uukbmsj01uczk2gdszw3c4l0-1-0.jpg

Oct 27, 2017 | 1985 Honda Prelude

1 Answer

93 honda prelude dohc vtec engine will not can be push started


Sounds like you accidently pulled the thin wire from you starter motor. Look at the connections at the end of the solenoid, mounted on starter motor.The thick red wire is Battery + next to that connection is a smaller male push- on terminal, locate loose wire (thin) in the same area and reconnect to male push-on terminal on solenoid or check if earth cable between body/battery to engine wasnt removed in the process.Also some vehicles you have to engage the clutch before starting, check for a switch located on clutch pedal where master cylinder connects to clutch pedal (Is clutch switch mounted and wiring connected?)

Jan 03, 2009 | 1993 Honda Prelude

Not finding what you are looking for?
1999 Honda Prelude Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...