Question about Cars & Trucks

Open Question

I need the torque for the head and cam 1999 DIAHATSU CUOURE eng- EJ-de 989cc

Cylinder head torque

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Posted on Sep 08, 2008

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the cylinder head torque settings for a hyundai getz 1.6 16 valve double overhead cam Engine cod G4ED


renew bolts
stage1- 30NM
stage2-90deg
stage3-individually slacken off 360deg
stage4-30NM
stage5-90deg

crank pulley bolt-142NM
cam sprocket bolt-88NM

i like to help people like you that give engine codes it makes it so much easier

Jul 20, 2016 | Hyundai Cars & Trucks

1 Answer

What is the engine bolts torque specs used


Selan Shaheed, probably best to get a workshop manual for that data.....that needs to be correct to ensure engine does not fail....Haynes may have one that you can access on line but you will need to search for it. I found several URLs that offer access to an on line PDF but the require you to fegister

Jul 12, 2015 | Cars & Trucks

1 Answer

Hi i need the cylinder head torque settings on a 4d34 mitsubishi eng


Mitsubishi 4d34T
'92-'94
3.9L
CID: 213
Rod Torque: 92 FT/LBS
Main Torque: 130 FT/LBS
Cylinder Head: 145FT/LBS

Feb 15, 2015 | Mitsubishi Cars & Trucks

1 Answer

Cylinder head torque 1999 wl eng


Cylinder Head Torque in 2 steps [1st (50 - 60 ft-lbs), 2nd (80 - 90 ft-lbs)]

Nov 05, 2012 | 1999 Mazda B2500

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

Cylinder head torque 1n diesel engine


Hi!

The Toyota Starlet is a fuel efficient compact car that replaced Toyota's Publica model in 1973 and was manufactured through the 1999 model year. The Starlet was sold new in the United States for only four years, from 1981 through the 1984 model year. Originally a rear-wheel drive car, the Starlet transitioned to front-wheel drive in 1984.

The 1981 to 1984 versions of the Starlet that were sold in the U.S. were powered by a 1.3 liter OHV engine with four cylinders and electronic fuel injection. The engine has a 2.95-inch bore and 2.87-inch stroke and produces 58 horsepower at 4,200 rpm. The 1981 and 1982 versions of the engine produced 67 ft-lbs of torque, and the 1983 and 1984 versions produced 74 ft-lbs of torque. The compression ratio is 9.5:1.
Hope that helps!!
EJ Kudelka

Nov 20, 2010 | 1984 Toyota Starlet

1 Answer

Whats the proper order and torque specs for a 99 32v northstar head?


REMOVAL & INSTALLATION NOTE: The manufacturer recommends that the entire powertrain be removed from the vehicle before removing the cylinder heads.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Powertrain assembly
    • Intake manifold
    • Cam covers
    • Harmonic balancer
    • Timing chain front cover
    • Oil pump
    WARNING
    Align all timing marks before performing the next step.
    • Chain tensioner from the timing chain
    • Cam sprockets
    NOTE: The timing chain remains in the chain case.
    • Timing chain guides, access for the retaining screws is through the plugs at the front of the cylinder head
    • Water crossover
    • Exhaust manifold
    • Cylinder head bolts by reversing the torque sequence
    • Cylinder head and discard the gasket
    WARNING
    With the camshafts remaining in the cylinder head some valves will be open at all times. Do not rest the cylinder head on a flat service with the cylinder face down, or valve damage will result. NOTE: Clean all gasket mating surfaces. Clean the head bolt holes in the crankcase. WARNING
    Be careful when cleaning aluminum gasket surfaces to prevent damage to the sealing surfaces.
  5. Check the cylinder head for warpage; it must be less than 0.002 in. (0.05mm). If the cylinder head was resurfaced, the dimension between the combustion chamber gauge pad and the deck surface must be at least 10.5mm. To install: NOTE: Refer to Section 1 of this manual for the cylinder head torque sequence illustration. The illustration is located after the Torque Specification Chart.
  6. Install or connect the following:
    • New cylinder head gasket
    • Cylinder head, lubricate the bolts with engine oil
  7. Torque the M11 bolts, in sequence, as follows:
    1. Step 1: 22 ft. lbs. (30 Nm).
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 180 degrees).
  8. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  9. Set the camshaft timing
  10. Camshaft guide bolt access hole plugs in the cylinder heads. The plugs should be seated and snug
  11. Install or connect the following:
    • Intake cam covers
    • Oil pump
    • Timing chain front cover
    • Harmonic balancer
    • Cam sprockets
    • Chain tensioner to the timing chain
    • Timing chain guides
    • Intake manifold
    • Water crossover
    • Exhaust manifold. Torque the nuts to 22 ft. lbs. (30 Nm) or the bolts to 18 ft. lbs. (25 Nm).
    • Powertrain assembly
    • Negative battery cable Fig. 1: Minimum head resurface dimension 7922vg04.gif

  12. Fill the cooling system.
  13. Evacuate and charge the air conditioning system.
  14. Run the engine and check for leaks.
prev.gif next.gif

Aug 19, 2010 | 1999 Cadillac DeVille

2 Answers

What are the cylinder head torque specs for a 1999 cadillac deville 4.6l


I can help you with this but I have to ask one question. Have you already taken this apart and putting it back together? Did you rethread all the head bolt holes because they strip out when you tighten them and you will ruin the head gaskets. Let me know, I have don't this job quite a few times. I'll have to look up the actual torque specs. Also you are wanting the spec for the cylinder head bolts and not the cylinder head cover bolts right?

Jun 12, 2010 | 1999 Cadillac DeVille

1 Answer

Cam shaft torques for caps and cover 3.0tdohc


Bolts in the center of the cams 28.2 ft/lbs
Bolts on the outside of the cams 15.9ft/lbs
INSTALLATION
1. Cylinder head cover.
1) Install the cylinder head cover gasket to cylinder
head cover.
3) Apply liquid gasket (TB1207B or equivalent) to
the rubber seal of the camshaft end, injector
harness gasket area and No. 1 camshaft
bracket.
4) Tighten cylinder head cover fixing bolts
Torque : 9 N·m (0.9 kg·m/6.5 lb ft)

Aug 11, 2009 | 2000 Isuzu Trooper

1 Answer

1999 Daihatsu Sirion


Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Aug 13, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...