Question about 1998 Honda Accord
My turning signal wont come on and my passenger side light don't come on either
There is a flasher unit normally where your fuses are it will be yellow or silver replace that and your turn signlas should work again. Some cars have a secondary one incase the flasher unit goes bad you still have your hazard lights. look to spend about 8.00 for the part at autozone.
Posted on Apr 19, 2014
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
*The Turn signal on the Side of the car next to the headlight*
1. Open the retractable headlights.
2. Remove the plastic shroud around the headlight: two screws in front and one on each side.
3. Look to the outside of the headlight and you will see a single screw in a small plastic cover on the front inside edge of the signal light assembly. The headlight prevents you from getting at the screw straight-on. I broke it loose with an offset phillips screwdriver, and then backed it out with a regular phillips.
4. Remove the plastic cover, and you will see two screws. Remove them.
5. Now you can pull the turn signal assembly forward and out.
6. To remove the bulb holders from the assembly, twist counterclockwise and pull out.
7. Pull straight outward to remove the bulbs. To assemble, follow the steps in reverse. Note that there are two plastic rods on the back end of the turn signal assembly that you will insert into two holes in the channel of the fender
*The turn signal in the bumper*
1. You will need a phillips head And Flat head screw driver, right below the turn signal there is a panel that you can pop out, (or its allready gone, Looks like a Fog light can go in there.)
2. once u find that, (Pretty easy to find) Look directly up in there., there is styrofoam up there and u will also notice a little hole,
3. Stick the Phillips head screw driver in that hole and turn it counter clockwize, The screw will not fall out,
4.once it feels like the screw is loose put the flat head in between the turn signal lense and bumper, the side where you unscrewed it and SLOWLY pry it out,
4. once out, just twist the plug and replace light bulb
to replace just reverse instructions
Posted on Jun 30, 2008
Check the prones inside the connector that you plug into the brake light module. You may have to squeeze, wiggle, tilt each one to see which one is not connecting all that good. I know it may sound confusing. I tried to explain the best of I could.
Posted on Apr 29, 2009
I assume you mean the one on the dash. This is an indicator that there is a problem in your braking system. Make sure it's not low on Brake fluid and have the brake system checked or check it yourself. If your going to check it yourself I recommend the Haynes repair manual on your vehicle as a reference.
Posted on Jul 30, 2010
Tips for a great answer:
Mar 14, 2016 | Honda Cars & Trucks
Mar 03, 2013 | 2003 Honda Accord
Jan 20, 2018 | 2000 Honda Accord
Oct 20, 2012 | Honda Accord Cars & Trucks
Aug 16, 2012 | 1992 Honda Accord
Apr 21, 2010 | 2003 Honda Accord
Apr 12, 2010 | 2004 Honda Accord
Jan 11, 2009 | 2003 Honda Accord
Aug 12, 2008 | 1992 Honda Accord
Jul 27, 2008 | 1994 Honda Accord
218 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: