Question about Cars & Trucks

Open Question

How to remove headlamp - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a headlight on a 1997 gmc sierra


Headlamp Removal & Installation To Remove:
  1. Turn headlamp switch OFF. gm-06-00-1046.gif

  2. Remove retaining ring screws.
  3. Remove retaining ring from headlamp.
  4. Remove headlamp from headlamp mounting bracket.
  5. Disconnect electrical connector from headlamp.
To Install:
  1. Connect electrical connector to headlamp.
  2. Install headlamp to headlamp mounting bracket.
  3. Install retaining ring to headlamp and install screws.
prev.gif next.gif

Feb 06, 2011 | 1997 GMC Sierra

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

Where is the wiper motor located


Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Headlamp Assembly Removal and Installation
  1. ssa~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HEADLAMP BULB AND RETAINER (13N021) ARE DROPPED. HANDLE BULB CAREFULLY. GRASP HEADLAMP BULB AND RETAINER ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HEADLAMP BULB AND RETAINER OUT OF REACH OF CHILDREN.
    NOTE: The headlamp (13008) on this vehicle does not need replacement when the headlamp bulb and retainer burns out. Refer to Headlamp Bulb for removal and installation of headlamp bulb and retainer .
    Position headlamp in the OFF position.
  1. Remove headlamp dash panel junction wire (14290) from headlamp bulb and retainers by grasping wires firmly and carefully snapping connector downward.
  1. NOTE: Use snap-ring pliers to spread headlamp mounting clips (13N129) , then pull straight upward to disengage.
    Remove three headlamp mounting clips attaching headlamp to radiator grille opening panel reinforcement (8A284) .
  1. Remove headlamp from vehicle.
  1. To install, reverse Removal procedure.
  1. Aim headlamp .

Oct 21, 2010 | 1999 Mercury Grand Marquis

1 Answer

How to change headlight in 2005 trailblazer


Its Pretty easy see instructions below



REMOVAL PROCEDURE
  1. Open and support the hood.
  2. Remove the grille.
  3. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
  4. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  5. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
  6. Remove the side marker socket (4) from the headlamp assembly.
  7. Remove the park/turn socket (3) from the headlamp assembly.
  8. Remove the headlamp assembly from the headlamp panel.
INSTALLATION PROCEDURE
  1. Position the headlamp assembly to the headlamp panel.
  2. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
  3. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
  4. Connect the headlamp electrical connector (2).
  5. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
  6. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
  7. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
  8. Install the grille

5285a5e.gif

Oct 20, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

I have a ford f350 and am trying to remove the old headlight assembly and replace with new one, can't seem to find out how to detach it from the truck


this for aero headlamp, plastic lens. please rate.

SECTION 417-01: Exterior Lighting 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly —Headlamp, Aerodynamic Removal
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp assembly.
    1. Pull up and remove the two upper headlamp clips.
    1. Release the lower headlamp clip.
    1. Position the headlamp so the connector can be accessed.
    1. Disconnect the headlamp connector.
Installation
  1. Install the headlamp assembly.
    1. Position the headlamp assembly.
    1. Connect the headlamp connector.
    1. Install the lower headlamp clip.
    1. Install the two upper headlamp clips.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment—Photometric Aiming or Headlamp Adjustment—Screen Method Aiming in this section.
      • d1d723b.gif

Aug 09, 2010 | 1999 Ford F350 Regular Cab

1 Answer

How to replace headlight bulb on 2002 chevy trailblazer


Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.
  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.
To Install:
  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.
Headlamp Assembly Chevrolet To Remove:
Headlamp Assembly (Chevrolet) gm-06-00-1591.gif

  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp assembly.
  6. Remove the headlamp assembly from the headlamp panel.
To Install:
  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

Jul 20, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Headlight replacement - 2002 Trailblazer


  1. Open and support the hood.Remove the grille.
  2. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
  3. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  4. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
  5. Remove the side marker socket (4) from the headlamp assembly.
  6. Remove the park/turn socket (3) from the headlamp assembly.
  7. Remove the headlamp assembly from the headlamp panel.
  8. Installation:
  9. Position the headlamp assembly to the headlamp panel
  10. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
  11. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
  12. Connect the headlamp electrical connector (2).
  13. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
  14. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
  15. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
  16. Install the grille. Refer to Grille Replacement .
  17. Close the hood

Oct 27, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Want to know how to replace my headlamp on my 1998 chevrolet silverado K1500 pick up truck. Do I have to remove the grille?


Nope! Here is the steps and a pic:


Headlamp Removal & Installation To Remove:
  1. Turn headlamp switch OFF
1afac03.gif
  1. Remove retaining ring screws.
  2. Remove retaining ring from headlamp.
  3. Remove headlamp from headlamp mounting bracket.
  4. Disconnect electrical connector from headlamp.
To Install:
  1. Connect electrical connector to headlamp.
  2. Install headlamp to headlamp mounting bracket.
  3. Install retaining ring to headlamp and install screws.

Mar 30, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

High beam bulb blown on buick rendezvous


  1. Open the hood.
  2. Remove the thumb screw from the back of the headlamp.
    761252.gif
    tif.gif
  3. Release the headlamp retainer by lifting up.
    755085.gif
    tif.gif
  4. Pull the headlamp straight forward, to release the ball stud from the grommet.
  5. Remove the headlamp from the upper fascia support.
  6. Disconnect the electrical connector from the headlamp.
    761255.gif
    tif.gif
  7. Remove the bulb(s) from the headlamp by rotating counterclockwise.
    761257.gif
    tif.gif
  8. Release the headlamp trim tabs from the headlamp, if required.
    761253.gif
    tif.gif
  9. Remove the headlamp trim from the headlamp, pulling to release the adhesive tape.
  10. Clean adhesive from the headlamp trim and headlamp using 3M™ adhesive remover P/N 8984, or equivalent.

Nov 26, 2008 | 2003 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...