Question about Chevrolet TrailBlazer

Open Question

Reset remote control - TrailBlazer Chevrolet Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My vehicule starts by itself it s equipped with a compustar remote starter


under the dash on drivers side you will find the remote starter controller, just unplug it and everything should still work fine. You might also find a fuse and you can just pull that out of the harness of the starter controller

Jan 23, 2015 | 2004 Chevrolet TrailBlazer

1 Answer

How do I reset the remote key


Try this it worked for my s60 and recently on my C30
S/V 90
Procedure
1. Sit in the vehicle with all doors closed.
2. Turn the ignition key on and off five times (not to start position, but the on position) and on the fifth time leave in the on position.
3. Press the remote lock/unlock button several times (if there is a dashboard mounted LED it should light for 2 seconds and then it should flash for 10 seconds) to synchronise the remote to the control unit. Repeat this for additional remotes.
4. Switch off the ignition and test the remotes. A maximum of 4 remotes can be programmed.
S/V90 (Alternative Method)
Procedure
1. Close all the doors, the bonnet and the boot.
2. Switch the ignition on and off 5 times within 10 seconds, and leave the ignition on the fifth time.
3. Press one of the two buttons on each remote control.
Note: The first remote control has to be programmed within 15 seconds. The rest must be programmed a maximum of 10 seconds apart from each other.
4. Switch off the ignition and test the remote controls.
If you are unsure how to program your remote controls, please contact your Volvo dealer.

Nov 06, 2013 | 2004 Volvo XC90

1 Answer

2001 maxima alarm not working but panic works


ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.

Here are some factory notes....FYI

Anti-Theft Systems

PROGRAMMING

NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.

PROGRAMMING > PROGRAMING NEW ID CODE

NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.

Please let me know if you need anything else to get the problem fixed. Happy mew Year!

Jan 03, 2018 | 2001 Nissan Maxima

1 Answer

I bought a honda civic sport 2005 got it resprayed and i built it up and now the alarm keeps going off the key fob doesnt work etheir the battery has been flat . does any body no how to reset the fob or...


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
IMMOBILIZER CAN ONLY BE SET BY DIAGNOSTIC EQUIPMENT

May 13, 2011 | 2005 Honda Civic

1 Answer

Lost original car alarm control... need to reset a new one...



programing a Nissan remote , is hidden secret by Nissan Dealers. As a Nissan Technician i will share it.

Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try.

Oct 29, 2009 | 2002 Volvo S40

2 Answers

C180 Auto car doors not responding to remote commands from key


hello,good day,first try to use your spare key,or check your fuse box at the rear,near your battery,if not corrected,send your car to a dealer for proper diagnose by using hht or star,ty

Jul 21, 2009 | 1988 Mercedes-Benz S-Class

1 Answer

Does any body know how to reset the ML350 alarm??....The remote control doesn't work after i replaced a new battery to the remote control. I couldn't even use the remote to lock/unlock the car. I was


SOME OF THE REMOTES REQUIRE THAT THE KEY BE IN THE IGNITION, IN THE ON POSITION. TAKE THE BATTERY OUT AND WAIT 10 MINUTES. THEN PUT THE KEY IN THE IGNITION AND INSTALL THE BATTERY WHILE THE KEY IS TURNED TO THE ON POSITION. HOPE THIS HELPS YOU. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK

May 18, 2009 | 2007 Mercedes-Benz ML350

1 Answer

Chevy Subruban 2007 remote control


you will have to take it to a chevy dealer to have it reset...

Feb 28, 2009 | 2005 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...