Question about Mazda Cars & Trucks

Open Question

Mazda etude problems

Hi I have a Mazda Etude 2002 160ie. The brake pedal travels to far before the car starts to brake I have changed the master cylinder pistons twice and bleeded the brakes properly. Any help would be of much help thanks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

elias_sgr
  • 163 Answers

SOURCE: Mazda etude alternator genarting excessive heat

1st off you would give everything a good visual examination. Look for loose alternator belt. Also look for wires that could have become disconnected or cut that leads to the alternator.

Then you would hook up a volt meter to the battery cables and check the voltage.
After this you would start the engine and recheck the voltage. The voltage on a charged battery should read around 12.5 volts. While the engine is running turn on a few accesories and speed up the idle a little the voltage should read around 14.5 volts.

If the voltage does not increase suspect either a faulty alternator or regulator.

Posted on Sep 09, 2008

  • 1 Answer

SOURCE: 1996 Mazda Etude 160 Timing Belt

The timing belt has 123 teeth, and ussualy the marks are little paints. align them together and then you will have ur problem solved.

Posted on Oct 24, 2008

dpjones1700
  • 26 Answers

SOURCE: timing belt setting and my car iddle are out of form mazda etude

Your camshaft and crankshaft pulleys have to be properly aligned upon installation of the timing belt. The cogs on the belt, should fit precisely with the teeth of the pulleys. Your # 1 engine cylinder should be moved to "Top Dead Center" before installing the belt. This means no compression once the top of the piston cylinder reaches the top of the chamber.

Posted on Nov 27, 2008

arauzvictor1
  • 466 Answers

SOURCE: no brake pressure on my 1991 mazda mpv, changed

you have to remove the pipes that go out of the master cylinder and purge the air later you connect the pipes and it purges the air in every auxiliary cylinder and the pedal will begin to have pressure

Posted on Dec 13, 2009

  • 62 Answers

SOURCE: just installed rebuilt master cylinder

If you are losing brake fluid you still have a leak in the system, if not then take it into a garage and have it pressure bled.

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda etude clutch problem


sounds like a throw out bearing to me but it could just be a spring popping

Jan 29, 2014 | Mazda Cars & Trucks

1 Answer

Mazda etude immobiliser problems


i lost my mazda etude immobiliser,when i try to cancell it,the engine only run for few seconds and stop.when i check the coils they are boilling i run out of ideas.

Feb 25, 2013 | Cars & Trucks

1 Answer

Mazda etude 1.6 i cut out while driving starting after about 10 min.


sounds like the coil pack is braking down when hot. check for spark while engine wont start

Nov 16, 2011 | 2003 Mazda MPV

1 Answer

My 160i etude 1997 misfires and even mazda agents


it is not carburated injectors are most likley leaking

Dec 15, 2009 | Mazda MAZDA3 Cars & Trucks

2 Answers

Mazda Etude 160ie timing


I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Jan 02, 2009 | 2004 Mazda 3

2 Answers

1996 Mazda Etude 160 Timing Belt


The timing belt has 123 teeth, and ussualy the marks are little paints. align them together and then you will have ur problem solved.

Jun 21, 2008 | 2004 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...