Question about 2005 Hyundai Getz 1.3

Open Question

Hyundai getz front wheel bearing set-up - 2005 Hyundai Getz 1.3

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 104 Answers

SOURCE: how to replace the front brake pads on a hyundai

Instead of explaining in words, here you find the right link to understand the disc barking system & how to relace the worn out pads.The link refers elantra, but the basic remains same for the GETZ.

http://www.cockeyed.com/lessons/brakeshoes/brakeshoes01.shtml

Posted on Jun 05, 2010

johnjohn2
  • 5763 Answers

SOURCE: how expensive is it to replace front wheel

It all depends where you live, the rate in ct is about 95.00 per hour and the time to replace a wheel bearing on this car is about two hours per side plus the parts and an aglinment,so it would cost about $400.00 in labor and the parts are not much, i would say for a good bearing about $30.00 and then the alignment which is about $69.99, you should shop around and try to get the best price. these bearings need to be pressed out and the new pressed in, heres a picture of the bearing , theres one on wheel, hope this is helpful.johnjohn2_70.jpg

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could cause a low pitched humming when excelerating in a 2006 huyandi getz.?


A wheel bearing maybe, or in a manual, the gearbox first motion bearing.

Another candidate is the differential, but in a FWD car this is usually nothing to worry about.

Dec 13, 2014 | 2006 Hyundai Getz 1.4

1 Answer

Constant loud humming from front of hyundai gets


If the noise get louder as you speed up, it is possibly a wheel bearing, needs checking out by a mechanic.

Jan 27, 2014 | Hyundai Cars & Trucks

1 Answer

How can i tell if my wheel bearings need to be replaced without pulling off parts for hyundai getz 2002


Sound comparison.
Jack up one front wheel, and securely block the other 3 wheels. Start the engine and put the car in gear, and let the motor run the wheel .
Do not race the engine.
Listen to the sound it makes.
Now shut off the engine and do the same to the other front wheel.
Is one really noisy ?
That's the problem wheel.
Unless you car was in a flood, wheel bearings usually last a lifetime on most cars.
Be blessed.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

How do i check if my wheel bearings need replacing on my hyundai geetz 2002 aust


Jack the front of the car up with the wheels off the ground grab the tire with both hands one at the top and 1 at the bottom and rock the tire up and down then switch your hands to the sides and rock the tire side to side if there is any movement in either direction replace the bearings. Also you can spin the tire while its off the ground and listen for bearing noise.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

Torque settings for 1.4 hyundai getz , main bearings


I need torque settings on hundai getz 1.4 Mains and big ends

Oct 20, 2012 | 2006 Hyundai Getz 1.4

1 Answer

Hyundai Getz - Passanger airbag or not...


If it says "airbag" on the stering wheel AND on the dash in front of the passenger,then it has a passengers side airbag.
Children are much safer in the back seat in the event of a collision.

Jul 02, 2009 | 2002 Hyundai Accent

1 Answer

2004 Hyundai Getz Noise in front


had same problem,believe it or not it was only a loose clamp on my cat- converter. jack her up and see hopefully same prob

Jul 05, 2008 | Hyundai Motor 2004 Accent

Not finding what you are looking for?
2005 Hyundai Getz 1.3 Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...