Question about Hyundai Getz

Open Question

Hyundai getz wheel bearing repacking - Getz Hyundai Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Ad
Puterwiz82
  • 60 Answers

SOURCE: 2002 Kia Rio rear wheel bearing passenger side

I'm from the United States, East coast.

Posted on Nov 24, 2008

emissionwiz
  • 76848 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

  • 740 Answers

SOURCE: replacing front wheel bearings on 2000 bonneville

No this ia a sealed bering. Its much easier to just change the bearing and replace the hub all in on shot. It also last alot longer. Good luck and thanks for using FIX YA

Posted on Mar 16, 2009

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I grease the wheels and what brand grease do I buy?


If you are repacking front wheel bearings on a car with disc brakes,you will want to buy wheel bearing grease suitable for the higher heat generated by the disc brakes.Any name brand wheel bearing grease will work as long as it is rated to be used on vehicles with disc brakes.
TIP: Do not wash the wheel bearings in solvent to clean them if they are in good shape and have no metallic particles in the existing grease.Just repack using the new grease to push the old grease out of the bearings.After wiping the hub clean add some clean grease evenly into the hub,install the repacked bearings and new seals and JUST SNUG the nut which adjusts the bearing and install a NEW cotter pin.

Apr 08, 2017 | Cars & Trucks

1 Answer

What could cause a low pitched humming when excelerating in a 2006 huyandi getz.?


A wheel bearing maybe, or in a manual, the gearbox first motion bearing.

Another candidate is the differential, but in a FWD car this is usually nothing to worry about.

Dec 13, 2014 | 2006 Hyundai Getz 1.4

1 Answer

Constant loud humming from front of hyundai gets


If the noise get louder as you speed up, it is possibly a wheel bearing, needs checking out by a mechanic.

Jan 27, 2014 | Hyundai Cars & Trucks

1 Answer

How can i tell if my wheel bearings need to be replaced without pulling off parts for hyundai getz 2002


Sound comparison.
Jack up one front wheel, and securely block the other 3 wheels. Start the engine and put the car in gear, and let the motor run the wheel .
Do not race the engine.
Listen to the sound it makes.
Now shut off the engine and do the same to the other front wheel.
Is one really noisy ?
That's the problem wheel.
Unless you car was in a flood, wheel bearings usually last a lifetime on most cars.
Be blessed.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

How do i check if my wheel bearings need replacing on my hyundai geetz 2002 aust


Jack the front of the car up with the wheels off the ground grab the tire with both hands one at the top and 1 at the bottom and rock the tire up and down then switch your hands to the sides and rock the tire side to side if there is any movement in either direction replace the bearings. Also you can spin the tire while its off the ground and listen for bearing noise.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

Torque settings for 1.4 hyundai getz , main bearings


I need torque settings on hundai getz 1.4 Mains and big ends

Oct 20, 2012 | 2006 Hyundai Getz 1.4

1 Answer

Mazda mpv 2006 repack wheel bearing


There is a little difference between the front and rear. The days of packing wheel bearing is almost over. The front bearing you have to pull the hub and change to bearing. The rear wheel you have to change out the hub bearing and all. The front is a sealed bearing and not serviceable. Please rate my answer so I am rewarded points for it.

Jan 29, 2012 | Mazda Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...