Question about 2008 Infiniti G35

Open Question

P0014 p0024 exhaust code engine - 2008 Infiniti G35

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code troubleshooting


It's your AVCS/cam shaft issue, bring the dealership since this issue is on Subaru TSB. Possible they replace the ECU/ECM unit.

02-132-12R Technical Service Bulletin Diagnosis and Repair for AVCS-Related DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021 and P0024

Jul 21, 2014 | 2012 Subaru Impreza 2.0i 4dr Hatchback...

1 Answer

OBDII Codes


P0014 - Exhaust Camshaft Position System Performance
P0973 - Shift Solenoid A Control Circuit Low
P0700 - Transmission Control System Malfunction

Dec 18, 2013 | 2010 Chevrolet Cobalt

1 Answer

Not working right


code p0014 refers to camshaft position(CMP) actuator . exhaust /right /rear bank 1--timing over advanced/system performance===causes valve timing--engine mechanical fault--CMP actuator . If you have done no work on the engine then I would be replacing the exhaust cam actuator (CMP actuator)

Nov 17, 2013 | 2002 Oldsmobile Bravada

2 Answers

Code p0014 exhaust and code p0015 exhaust


The code P0014 is for Camshaft Positon Sensor Actuator Bank 1. The possible causes are incorrect camshaft timing, wiring problems (harness/wiring) in intake timing control valve solenoid system; continuous oil flows to VCT piston chamber or failed timing valve control solenoid(stuck open).
The code P0015 is for Camshaft Position -Timing Over-******** (Bank 1). Your problem will probably be that the timing will be slightly out, due to wear (stretch) of the timing chain; this will all be linked to the overall cold start issue and the timing position. Get that timing checked, or push for the full fix for the cold start timing issue.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

Check engine light code p0014 exhaust and p0015 exhaust


P0015: Camshaft Position, Act B - bank 1, timing over

P0014: Camshaft Position, Act B - bank 1, timing over advanced
Check oil level and quality.
Remove n clean exhaust camshaft vanost actuator.
Do not refit to exhaust cam, but swap with inlet actuator.
clear codes...if eml on again see if fault moved to inlet cam. If so replace the actuator.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

Diagnostic code p0013, p0014


Diagnostic Test Code (DTC) P0013 is "Exhaust Cam Position (CMP) Actuator Solenoid Control Circuit"
Diagnostic Test Code (DTC) P0014 is "Exhaust Cam Position (CMP) System Performance"

DTC P0014 can be caused by several things that can affect your variable cam timing system performance including using the wrong viscosity engine oil. However, since you have the DTC P0013, it is pretty obvious that the problem is being caused by a circuit malfunction in the control solenoid circuit. It could be as simple as a loose connection at the solenoid electrical connector. It could be that the solenoid itself has an open circuit in its coil windings, or it could even be caused by squirrels or mice chewing on the wiring harnesses in your engine compartment. You must diagnose the circuit to find the cause. Fixing the control solenoid circuit will most likely make both of these codes go away.

Dec 17, 2011 | 2006 Chevrolet HHR

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

Not finding what you are looking for?
2008 Infiniti G35 Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14185 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...