Question about Cars & Trucks

Open Question

Isuzu oil pressure

Oil pressure of oil pump did'nt reach valve trains and rocker arms, what are the probalbe cause?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: 1993 TOYOTA TERCEL 1500cc Valve Seals Replaced now smokes much worse

You either have had the wrong valve seals installed, they are physically missing, or the valves are incorrect (too loose in the guides/stem too thin). The rocker arm seals will not contribute to your issue. If it did not have the oil smoke before you took the head off, the issue is with whatever the machine shop did. Valve seals have to fit TIGHT, or oil will go down the valve stem into the intake.
Take the head back to the machine shop & tell them to fix it. For free.

Posted on Sep 27, 2008

Ad
  • 2 Answers

SOURCE: I have a 2000 Dodge

are the pushrods hollow or solid

Posted on Apr 01, 2009

seanpwright
  • 2030 Answers

SOURCE: 1994 mitsubishi mighty max valve tapping

How many miles?
Could be a bent pushrod.
Could be just a high mile engine that needs overhauld.
Could be you engine needs higher octane fuel...as engines get older and worn they will benifit from higher octane.

Posted on Sep 14, 2009

  • 2309 Answers

SOURCE: 2003 Chevy Malibu, oil

could be a bad oil filter, plugged sump pick up tube screen, have a mechanical oil guage installed to ge an accurate reading, althoug i suspect if the engine is making noise it may be damaged, best to remove the oil pan for inspection, metal shavings in the bottom indicate serious problems

Posted on Oct 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What's causing valve tapping?


Some tapping is normal with age and mileage. Wear on the cam and lifters and followers causes it.

Apr 08, 2016 | Cars & Trucks

1 Answer

Installed new oil pump and now have broken rocker arms


THe rocker arms are broken because there was not enough downward movement in the valves to allow the cam to complete its turn. IT happens when the valve spring retainer either hits the top of the valve guide or the valve springs are fully compressed forming a solid block . If you have hydraulic valve adjusters I would be suspicious of a lack of movement (seized) in the ones that broke the rocker arms

Feb 20, 2013 | Ford F-150 Cars & Trucks

1 Answer

My 2005 cadillac cts makes a knocking noise when i step on the gas pedal, then stops when it reaches 5 mph


Hi there:
First check this information about "engine noses"...
ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.

First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.

COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.

VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.

To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).

On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.

DAMAGED ENGINE PARTS NOISE
Inspect the valvetrain components. Excessive wear on the ends of the rocker arms, cam followers (overhead cam engines) and/or valve stems can open up the valve lash and cause noise. So too can a bent pushrod or a broken valve spring.

RAPPING OR DEEP KNOCKING ENGINE SOUND
Usually bad news. A deep rapping noise from the engine is usually "rod knock," a condition brought on by extreme bearing wear or damage. If the rod bearings are worn or loose enough to make a dull, hammering noise, you're driving on borrowed time. Sooner or later one of the bearings will fail, and when it does one of two things will happen: the bearing will seize and lock up the engine, or it will attempt to seize and break a rod. Either way your engine will suffer major damage and have to be rebuilt or replaced.

Bearing noise is not unusual in high mileage engines as well as those that have been neglected and have not had the oil and filter changed regularly. It can also be caused by low oil pressure, using too light a viscosity oil, oil breakdown, dirty oil or dirt in the crankcase, excessive blowby from worn rings and/or cylinders (gasoline dilutes and thins the oil), incorrect engine assembly (bearings too loose), loose or broken connecting rod bolts, or abusive driving.

Bearing wear can be checked by dropping the oil pan and inspecting the rod and main bearings. If the bearings are badly worn, damaged or loose, replacing the bearings may buy you some time. But if the bearings are badly worn or damaged, the crankshaft will probably have to be resurfaced - which means a complete engine overhaul or replacing the engine is the vehicle is worth the expense.

ENGINE PINGS OR KNOCKS WHEN ACCELERATING
The cause here may be Spark Knock (Detonation) caused by an inoperative EGR valve, overadvanced ignition timing, engine overheating, carbon buildup in the combustion chambers, or low octane fuel.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | 2005 Cadillac CTS

1 Answer

I hear knocking on my 2005 equinox what could couse the knocking is it the oil pump and how do I replace it


Hi there:
Firs I suggest check this information about "engine noses"...
ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.

First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.

COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.

VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.

To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).

On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.

DAMAGED ENGINE PARTS NOISE
Inspect the valvetrain components. Excessive wear on the ends of the rocker arms, cam followers (overhead cam engines) and/or valve stems can open up the valve lash and cause noise. So too can a bent pushrod or a broken valve spring.

RAPPING OR DEEP KNOCKING ENGINE SOUND
Usually bad news. A deep rapping noise from the engine is usually "rod knock," a condition brought on by extreme bearing wear or damage. If the rod bearings are worn or loose enough to make a dull, hammering noise, you're driving on borrowed time. Sooner or later one of the bearings will fail, and when it does one of two things will happen: the bearing will seize and lock up the engine, or it will attempt to seize and break a rod. Either way your engine will suffer major damage and have to be rebuilt or replaced.

Bearing noise is not unusual in high mileage engines as well as those that have been neglected and have not had the oil and filter changed regularly. It can also be caused by low oil pressure, using too light a viscosity oil, oil breakdown, dirty oil or dirt in the crankcase, excessive blowby from worn rings and/or cylinders (gasoline dilutes and thins the oil), incorrect engine assembly (bearings too loose), loose or broken connecting rod bolts, or abusive driving.

Bearing wear can be checked by dropping the oil pan and inspecting the rod and main bearings. If the bearings are badly worn, damaged or loose, replacing the bearings may buy you some time. But if the bearings are badly worn or damaged, the crankshaft will probably have to be resurfaced - which means a complete engine overhaul or replacing the engine is the vehicle is worth the expense.

ENGINE PINGS OR KNOCKS WHEN ACCELERATING
The cause here may be Spark Knock (Detonation) caused by an inoperative EGR valve, overadvanced ignition timing, engine overheating, carbon buildup in the combustion chambers, or low octane fuel.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 22, 2012 | Cars & Trucks

1 Answer

Knocking in the motor


Hi there:

Check this information about "engine noses"...

ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.

First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.

COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.

VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.

To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).

On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.

DAMAGED ENGINE PARTS NOISE
Inspect the valvetrain components. Excessive wear on the ends of the rocker arms, cam followers (overhead cam engines) and/or valve stems can open up the valve lash and cause noise. So too can a bent pushrod or a broken valve spring.

RAPPING OR DEEP KNOCKING ENGINE SOUND
Usually bad news. A deep rapping noise from the engine is usually "rod knock," a condition brought on by extreme bearing wear or damage. If the rod bearings are worn or loose enough to make a dull, hammering noise, you're driving on borrowed time. Sooner or later one of the bearings will fail, and when it does one of two things will happen: the bearing will seize and lock up the engine, or it will attempt to seize and break a rod. Either way your engine will suffer major damage and have to be rebuilt or replaced.

Bearing noise is not unusual in high mileage engines as well as those that have been neglected and have not had the oil and filter changed regularly. It can also be caused by low oil pressure, using too light a viscosity oil, oil breakdown, dirty oil or dirt in the crankcase, excessive blowby from worn rings and/or cylinders (gasoline dilutes and thins the oil), incorrect engine assembly (bearings too loose), loose or broken connecting rod bolts, or abusive driving.

Bearing wear can be checked by dropping the oil pan and inspecting the rod and main bearings. If the bearings are badly worn, damaged or loose, replacing the bearings may buy you some time. But if the bearings are badly worn or damaged, the crankshaft will probably have to be resurfaced - which means a complete engine overhaul or replacing the engine is the vehicle is worth the expense.

ENGINE PINGS OR KNOCKS WHEN ACCELERATING
The cause here may be Spark Knock (Detonation) caused by an inoperative EGR valve, overadvanced ignition timing, engine overheating, carbon buildup in the combustion chambers, or low octane fuel.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 26, 2012 | 1990 Isuzu Trooper

2 Answers

Knocking in the motor


Check this information about "engine noses"...

ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.

First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.

COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.

VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.

To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).

On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.

DAMAGED ENGINE PARTS NOISE
Inspect the valvetrain components. Excessive wear on the ends of the rocker arms, cam followers (overhead cam engines) and/or valve stems can open up the valve lash and cause noise. So too can a bent pushrod or a broken valve spring.

RAPPING OR DEEP KNOCKING ENGINE SOUND
Usually bad news. A deep rapping noise from the engine is usually "rod knock," a condition brought on by extreme bearing wear or damage. If the rod bearings are worn or loose enough to make a dull, hammering noise, you're driving on borrowed time. Sooner or later one of the bearings will fail, and when it does one of two things will happen: the bearing will seize and lock up the engine, or it will attempt to seize and break a rod. Either way your engine will suffer major damage and have to be rebuilt or replaced.

Bearing noise is not unusual in high mileage engines as well as those that have been neglected and have not had the oil and filter changed regularly. It can also be caused by low oil pressure, using too light a viscosity oil, oil breakdown, dirty oil or dirt in the crankcase, excessive blowby from worn rings and/or cylinders (gasoline dilutes and thins the oil), incorrect engine assembly (bearings too loose), loose or broken connecting rod bolts, or abusive driving.

Bearing wear can be checked by dropping the oil pan and inspecting the rod and main bearings. If the bearings are badly worn, damaged or loose, replacing the bearings may buy you some time. But if the bearings are badly worn or damaged, the crankshaft will probably have to be resurfaced - which means a complete engine overhaul or replacing the engine is the vehicle is worth the expense.

ENGINE PINGS OR KNOCKS WHEN ACCELERATING
The cause here may be Spark Knock (Detonation) caused by an inoperative EGR valve, overadvanced ignition timing, engine overheating, carbon buildup in the combustion chambers, or low octane fuel.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 26, 2012 | Isuzu Trooper Cars & Trucks

1 Answer

I have no oil pressure in the car we pulled the valve cover today and found 6 of the rocker arms were not installed, we havent pulled the other cover yet however with this not installed would this affect...


Hi,
are you serious? Aside from that question. If there are rocker arms missing it could affect the oil pressure. Are the oil feed holes in the area of each missing rocker plugged off?

Perhaps I had better back-track here. If the oil lube system has no restrictions in it then there will be minimal oil pressure developed. The oil pump will be pumping oil to the lower end of the engine and that will be where oil press if any will be developed.

The rocker area has drillings which restrict the oil delivery from the pump, however, the rocker arms themselves offer resistance to the oil supply and the oil must have enough flow and pressure to form a circle of oil within the rocker arm and thus keep it clear of the shaft. The oil flow goes through the rocker arm, and down over the valves and pushrods,(if fitted) and drops back down into the oil pan. Different set ups can be used, but that's a basic configuration.

The engine lubrication is designed with certain resistances, and they in turn affect the flow of oil and the pressure developed by the pump.

Good luck.

Jan 29, 2011 | 1991 Mitsubishi 3000GT

1 Answer

Oil pressure is fine. Oiling only to the pass side valve train.


The 3.1/3.4 engines are built the same way. The oil goes through the cam bearings then to the lifters, then the push rods to the rocker arms. The last engine I seen that had a weird problem had the cam bearings spun. Unfortunately there is no easy way to check for this problem short of disassembling the engine.

The other possibility would be bad lifters but loosing half of the engine lifters wouldn't be possible. Sometimes the pushrods wear on the contact areas also but not usually half an engine.

This isn't going to be easy, Good luck.

Nov 02, 2009 | 2005 Chevrolet Impala

2 Answers

I have an Isuzu Rodeo 3.2 L when the engine is cold, motor sound good oil pressure is between 30 and 55 as it starts to get hotter oil pressure drops and the rocker arms start to rattle. When engine is...


The oil pressure in an engine will naturally drop off as the engine warms up. If the oil pressure is dropping too much it could be cause by several things. I don't know how many miles your engine has on it but the oil pump may be getting weak and may need to be replaced. Worn out cam bearings or crank bearings can also cause low oil pressure. Sounds like your engine may be ready for a rebuild

Jul 16, 2009 | 2002 Isuzu Rodeo

4 Answers

TAPPING IN VALVES


ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.
First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.
COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.
VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.
To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).
On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.

Let me know if you have any other questions.  Thanks for rating my response and for using FixYa!

May 28, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...