Question about 2011 Mazda 3

Open Question

2004 MAZDA 626 ENGINE runs but the shifter won't shift into Rev or drive

It was working just fine earlier today

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jmpienaar1
  • 5 Answers

SOURCE: '98 Mazda 626 Died and will not start again..HELP

b_bro

Check the Fuel injection system (injectors) and the intake manifold. It might also be wise to check the alternator as well as the starter coil and also the electronic distributor

Posted on Oct 18, 2008

Ad
  • 297 Answers

SOURCE: 1999 Mazda 626 no rear lights!

fuse or wire harness, checked the voltage present in the fittings? Switch on before checking.
you get 12 volts more or less?

Posted on Apr 15, 2009

rcampsr
  • 90 Answers

SOURCE: My Mazda 626 Wont go into Drive

Sounds like you have lost the transmission. There are bands that clamp down to lock the transmission into the gear you want. They are controlled by a hydrolic unit located in the trans. The first thing I would do is have a shop pull the trans oil pan and see if it is full of chips of metal. If so you definately have a problem. At the same time they can look at the bands and see if one of them is broken. another cause would be that metal has gotten into the hydrolic valve body and frozen the drive band portion so it will not function. You may also get lucky and have it be an internal adjustment of the drive band. Good Luck, RAC

Posted on Apr 18, 2009

  • 6982 Answers

SOURCE: 95 mazda protege stuck in drive, wont shift gears, shifter moves but can't go in reverse, need help please

Check the shift cable that goes between the shifter and the transmission. If it's damaged internally it will not move properly and the condition you stated will be a symptom. Easiest way to check it is to disconnect the transmission end of cable and see if it moves freely. If not, replace it.

Posted on Jun 02, 2009

  • 30 Answers

SOURCE: transmission in 1996 mazda 626 slow to shift high rpm

if its reving high then shifting then your trannys going

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I can shift into drive but it won't engage


sounds like a broken shift cable. (the connection between the shifter and the gearbox) common symptoms are the shifter move easier than normal.and does not move to any gears (not even park or neutral).

Nov 23, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

97 mazda 626 wont shift from park. release button on side of shifter wont push in. removed knob, plastic rod in center wont move


The 1st thing you need to do is check the brake lights, if they are not wiorking the park lock solenoid doesn't get power and the park lock remains engaged.

Apr 17, 2012 | 1997 Mazda 626

1 Answer

My1991 mazda 626 will not rev up over 3000 rpm


DO YOU MEAN WHEN YOU ARE ACCELERATING? Or do you mean sitting and reving the engine? If you are just reving the engine in park then the rev limiter is kicking in.

Feb 07, 2012 | 1991 Mazda 626

1 Answer

I have a 99 mazda 626 runs and starts fine but stalls when coming to idle i already changed maf sensor


check and or clean the (IAC) idle air control, this is what controls idling on most of todays cars and light trucks. if iac is removed for cleaning. clean out where it mounts to engine or fuel injection unit. good-day !

Jan 31, 2012 | 1999 Mazda 626

2 Answers

I have mazda 626 does not move when you put the shifter in any gear.


Follow your shift arm on the trans- they had a cheap nylon snap socket to hold them on

May 26, 2011 | 1984 Mazda 626

1 Answer

Pops out of 5th gear


You're 5th gear syncro has just gone out. It keeps your shift forks and slider gear from popping off. It also makes it possible to shift the gear in. It's going to take a rebuild of the transmission to fix this problem.

Nov 17, 2009 | 1999 Mazda 626

1 Answer

I have a 1996 mazda 626 automatic , how do you un-lock the shift lock ?


Have same problem. smacking it worked for a while and now i have to leve a spare key in the little keyhole by the shifter.

Sep 28, 2009 | 1996 Mazda 626

6 Answers

Mazda 6 shifter cables broken


I had this same issue last week with my 2005 Mazda 6 Manual.... I feel your pain. About $275 for the new Cable and another 300 to install it.

Jun 22, 2009 | 2005 Mazda 6

1 Answer

1993 mazda 626: could not get trans out of park!


Ignition lock is activated: You over rode it but still have original problem. Alarm system might be confused. SO....

1 disconnect battery negative (-) cable(make you have radio code if any) to reactivate radio, which works anyway if code was never set.

2 press brake peddle for 5 seconds

3 reconnect negative cable to battery.

use key and twist diver door lock to OPEN (this resets alarm which might have caused ignition lock module to activate.

You should be able to turn on the ignition, start the engine and shift out of park. Hope this helps.

Jun 10, 2009 | 1993 Mazda 626

Not finding what you are looking for?
2011 Mazda 3 Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...