Question about Dodge Neon

Open Question

How remove transmission cooling lines from radiator 2005 neon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22156 Answers

SOURCE: How do I remove the radiator from a 2003 S60?

cant say i have worked on one of these YET but if their is no obvious connection just a compression join then take it off the other end as it could be all one piece with the rad

Posted on Feb 13, 2009

Ad
oneStan
  • 430 Answers

SOURCE: removing the transmission cooling line fron

These lines just run straight through the radiator to provide cooling. You can bypass the radiator by adding a transmission fluid cooler, during the cold weather in a pinch, a replacement transmission hose with 2 clamps can be connected between the 2 transmission lines to correct leakage, but in warm weather, the fluid suffers if it doesn't get the benefit of a cooler.

Aftermarket coolers are relatively inexpensive, especially compared to the long term benefit of keeping the fluid degrees cooler, prolonging the life of the trans.

good luck

Posted on Feb 22, 2010

BCAS1298
  • 3092 Answers

SOURCE: removal of transmission cooling lines from

Yes, it's call a line disconnect tool, Napa has this tool part # 7759086 cost about $8.00.Also can be used for fuel filter line.

Posted on Jul 07, 2010

airjer995
  • 5332 Answers

SOURCE: need to replace the transmission cooling lines

they are a type of quick connect fitting. There is a special tool just for these types of fittings. If you remove the plastic cover that goes over the fitting you will see a metal clip in a groove. You can use a small pick to carefully remove the clip (they go flyin and get lost easily but they are available from your local GM dealer or parts store). Once the clip is removed you will be able to pull the line out of the radiator/transmission fitting.

Reinstall the clip after you remove the line. The new line will slide in and click into place.

Posted on Oct 13, 2010

vetteman3002
  • 2299 Answers

SOURCE: I have a 2003

No the transmission fluid will not hurt the water pump at all. And water won't destroy the transmission unless it has been over a long period of time. I would have both flushed. The cooling system and the transmission. If you don't flush the coolant system the transmission fluid will turn to a gummy substance and will plug up your heater core.

Posted on Nov 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove radiator on 2000 Lincoln Continental


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove the radiator.

Oct 21, 2016 | Lincoln Cars & Trucks

1 Answer

01 neon coolant in transmission fluid


Your transmission lines are cooled from the radiator. You will need a new radiator or get the one you have refurbished if possible

Aug 21, 2012 | Cars & Trucks

1 Answer

Radiator installation on 2003 Kia Sorento


That is a VERY easy radiator.
Loosen radiator drain plug and drain coolant from radiator.
Disconnect cooling fan connectorsRemove upper and lower radiator hoses after marking them to ease installation.
For vehicles equipped with automatic transaxles, disconnect transmission cooler lines at transaxle.
Remove air conditioner condenser fixing bolts and radiator bracket fixing nuts.
Remove the radiator, radiator cooling fan, air conditioning cooling fan and transmission cooler lines from the vehicle as an assembly.
Transfer all necessary parts (fan assemblies, cooler lines, clips, speed nuts, fittings, etc.) to the new radiator.

Reverse procedure to install.

Fill and bleed cooling system.

Apr 14, 2012 | 2003 Kia Sorento

1 Answer

Trans axle light comes on


Your transmission is probably overheating. How many miles are on the vehicle, and have you had the transmission fluid flushed, and filter changed lately?

You could 1st start checking the fluid flow thru the radiator cooling lines by removing the lower trans. cooling line, aim the hose into a drain pan then starting the vehicle in park with an assistant. Make sure you are getting good circulating flow from the cooling return hose. The radiator coolers can plug partially with clutch material and cause an obstruction. A cooling line backflush would be needed to clear it.

If fluid flow is good, I would also change the transmission filter to make sure it is not a fluid obstruction there. Make sure you use mercon V fluid and don't overfill the transmission level while replacing the drained out fluid amounts.

The transaxle light blinking will set codes in the computer and you will need a transmission scanner code reader to have them read, usually a good repair shop or dealer can help.

Jun 16, 2011 | 2005 Ford Freestar

1 Answer

Need to replace the transmission cooling lines from radiator to transmission. Are the ends just screwed into the radiator or are they pressed


they are a type of quick connect fitting. There is a special tool just for these types of fittings. If you remove the plastic cover that goes over the fitting you will see a metal clip in a groove. You can use a small pick to carefully remove the clip (they go flyin and get lost easily but they are available from your local GM dealer or parts store). Once the clip is removed you will be able to pull the line out of the radiator/transmission fitting.

Reinstall the clip after you remove the line. The new line will slide in and click into place.

Oct 13, 2010 | 2005 Buick LaCrosse

1 Answer

My car is overheating. i got water in my transmission, and transmission fluid in my water. is it my radiator? can my transmission cooling lines be backwards? my car is not smoking and no water is comming...


Sounds like the transmission cooler tank with in the radiator has gone bad, the transmission lines can go on either way, does not matter, replace radiator and have cooling system flush and have a transmission flush also done.

Jul 08, 2010 | 2000 Plymouth Neon

2 Answers

Removing the transmission cooling line fron


These lines just run straight through the radiator to provide cooling. You can bypass the radiator by adding a transmission fluid cooler, during the cold weather in a pinch, a replacement transmission hose with 2 clamps can be connected between the 2 transmission lines to correct leakage, but in warm weather, the fluid suffers if it doesn't get the benefit of a cooler.

Aftermarket coolers are relatively inexpensive, especially compared to the long term benefit of keeping the fluid degrees cooler, prolonging the life of the trans.

good luck

Feb 22, 2010 | 1996 Dodge Ram

3 Answers

Would the engine over heating on my 2002 dodge neon cause my transmition to slip?


No, this is not related. You just happen to lucky enough to have two problems at the same time. If the engine got to a point where is was glowing hot, it could transfer the heat to the cooling lines causing air bubbles in the fluid and henceforth a slipping tranny. However, your engine would seize solid forever given those circumstances.

Sep 08, 2009 | 2002 Dodge Neon

1 Answer

How do i replace the radiaor? on this 2005 Hyundai do i remove the intake cover, then the cooling fan, the the motor mount? what?


Below are instructions and a diagram for removing the radiator from your Santa Fe. There's nothing involving the motor mounts. Best of luck and please post back with any questions or just to rate the solution. Greg

  1. Drain the cooling system. Remove the radiator cap to speed draining.
  2. Remove the inlet hose from the radiator.
  3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
  4. Remove the fan shroud clip from the condenser tubes.
  5. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
  6. Remove the air deflectors from the top of the radiator.
  7. Remove the cooling fan shroud bolts.
  8. Remove the coolant reservoir hose from the radiator overflow neck.
  9. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
  10. Disconnect the engine cooling fan motors electrical connectors.
  11. Remove the cooling fan motors electrical harness from the fan shroud clips.
  12. Remove the cooling fan shroud.
  13. Remove the outlet hose from the radiator.
  14. Disconnect the transaxle oil cooler pipes from the radiator.
  15. Tilt the top of the radiator rearward.
  16. Remove the condenser hold down bracket from the radiator.
  17. Lift the condenser from the mounting tabs on the radiator and position the condenser aside.
  18. Remove the radiator.
6db9db4.gif

Aug 11, 2009 | 2005 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...