Question about Cars & Trucks

Open Question

Allison transmission fault codes

Fault 0894 coming up

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Freightliner sprinter and could I do a ECU reset on my automatic trans? My trans is shifting a little funky. Thank you.


possible but the only place to do it would be an accredited freight liner service center or allison transmission shop
the main faults will be shown if you first get a fault code reading rather than resetting as resetting will not fix faulty sensors

May 07, 2017 | Cars & Trucks

1 Answer

Mercedes benz fault codes


0894 is transmission slip
2732 also has to do with the transmission

Sep 06, 2014 | Cars & Trucks

1 Answer

Problem with a 2003 Dodge Ram, fault codes indicate a transmission Malfuncting.Tcm scan reveals pressure switch open or closed at wrong time.


Transmission solenoids are usually installed in a transmission valve body, Transmission Control Unit, or transmission control module. If you have a question about a specific Allison Transmission model, you should call Allison Transmission Here is the number for the Texas Distribution office 214-631-5370-----------------------------------------------------------------------------
vas 5054a

Nov 28, 2012 | Cars & Trucks

1 Answer

Truck will not shift. Service engine soon light is on when this happens. Truck has the allison I believe it is the 1000 Six speed transmission. Runs about 2500 RPM at 35 miles an hour if that helps to know...


First you need to have the codes read. When the light comes on it stores a code, even if the light goes back out. Transmissions run off various sensors, MAF, TPS, Transmission range sensor. One of these start messing up and so does the transmission, plus other engine related problems. Get the codes and let me know.Randy

Feb 27, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

Will a transmission from 2003 duramax fit in a 2004 duramax?


They will deefinitely providing the 2 are the same model. In 2004 the Allison tranny was available in a 5 or a 6 speed. Before 2004 only the 5 speed was used. If one is changed for the other there will be shifting issues and codes set in both the ECM (engine control computer) and TCM (transmission control computer). Make sure you are putting in a 5 speed Allison tranny.

Jan 29, 2011 | GMC Sierra Cars & Trucks

3 Answers

THE CODE P1710 CAME UP WHAT IS IT


that code dosent ring a bell right off hand but you can go to a auto-zone and they will tell you exactly what it means for free. hope this helps .

Jan 30, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

01 duramax allison changed fluid and filters now in limp mode


Make sure you have the proper amount of tranny fluild in it and get that Valvoline fluid out of it. Allison transmissons have there own type of tranny fluid and you want to use it. You can buy the right stuff from a Allison dealer. Most Detroit Diesel dealers are also Allison dealers. Look them up in your phone book and they will tell you the quanity and sell you five gallon pails of the fluid. Just get the serial number off of the side of the transmisson before you call. Change the fliters again too. Believe me, this is important. My company has Yard horses with Allison transmissions and you don't want to screw with the small stuff. Service them right and they work as hard as you want.

Aug 01, 2009 | 2002 Chevrolet Silverado

1 Answer

Having a problem with my allison md 3060 transmission


Hi mate I had the same problem with a camper once and the only way that you will ever stop it from shifting hard into gears down shifting or up is to take it into a Detroit Allison work shop and ask them to reset the throttle position and reset Un-adaptive shifts then to do an Fast-adaptive shift with the electronic tool called Allison Doc.

Ask them also to do a clutch report on the electronic tool, that will tell you straight away the condition of the box on the inside.

Thats the problem with these new electronic transmissions they force you to go back to the suppliers. If I had my book here I could have helped you with the fault code but you would have had to take it in any way to get all the parameters reset.

What happens is that when you buy this trans new they set it to UN-adaptive shifts then to fast adaptive then it learns how long the solinoids should be open and how quick to open them to have a good shift, but over a few ignition cycles the fast-adaptive changes to normal over a year or two the clutch plates wears with a few 001 and the computer cant keep up have to be reseted which is normal to them, expect to take it back every year or two to be reseted.

Mar 20, 2009 | 1999 Ford Super Duty F 450

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...