Question about 1996 Ford F250 Crew Cab

Open Question

Where is the idle air control valve located on a 7.3 diesel?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fixincars
  • 335 Answers

SOURCE: idle control

The Idle control Valve will not in most cases help you check for a vacuum leak that csuses High Idle in Taurus a lot check for the PCV hose.

Posted on Jul 29, 2008

Ad
emissionwiz
  • 76682 Answers

SOURCE: were is the idle air control valve located on my

at the throttle control valve in the upper intake manifold. has 2 wires to it, is a long and round and about 8 inches long.

Posted on Dec 11, 2009

  • 532 Answers

SOURCE: cant loc the idle air control vavlve located on a 1988 crown vic

attached to the throttle body,looks like an electric motor bolted to a square piece with the corners notched out,with 2 wire connector on the end.

Posted on Feb 19, 2010

sscullys
  • 984 Answers

SOURCE: Iac valve

The 04-08 MY F-150 do not have a IAC with throttle by wire.

The PCM operated the intake butterfly with a small stepper motor for both normal acceleration and to keep enough air in the system to allow the truck to idle correctly.

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 land rover freelander idle air control valve location?


there is 2 valves and are located on the rear of engine on the left has you look from under the hood

Oct 13, 2017 | Land Rover Cars & Trucks

1 Answer

My opel corsa utility not starting low idle


Petrol or diesel? If it's the petrol model.....these cars have known issues with their IAC valve (idle air control valve). It's situated just before the butterfly on the intake manifold. Usually black plastic with 3 wire plug connection. They control the idling by controlling the amount of air bypassing the butterfly at idle speeds. Sometimes you can fix it by removing the unit and spray it with lubricant and cleaning it. Best way is to just replace it.

May 15, 2017 | Opel Cars & Trucks

1 Answer

Where is the idle air control valve wiring harness located on a 2001 ford windstar


idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-0.jpg

idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-2.jpg


idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-9.jpg

idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-14.jpg this is the idle air control and the plug the wires may not be the same color the valve is located on the throttle body the photo's will make it easier to find it

Apr 05, 2015 | 2001 Ford Windstar LX

2 Answers

2003 idle control valve location


On the throttle body just before the hose to the air cleaner.
Should be black with three wires.

May 13, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Where is the idle control valve located on a 2000 ford half ton van


The idle air control valve (IAC) is located on the throttle body.this valve allows for sir to bypass the throttle plate when closed in order get air in to the engine

Mar 01, 2013 | Cars & Trucks

1 Answer

After sitting, hard to start, seems not to be getting fuel. you can spray starting fluid and it starts, must run at higher than normal idle for a few minutes, then will idle normally.


OPERATION The Idle Air Control (IAC) valve controls the engine idle speed and dashpot functions. The valve is located on the throttle body on. This valve allows air to bypass the throttle plate. The amount of air is determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal. Fig. 1: Cleanable IAC valve — 5.0L engine version shown, others similar 88484g22.gif
Fig. 2: Non-cleanable IAC valve — 5.0L engine version shown, others similar 88484g23.gif
prev.gif next.gif TESTING OBD-I System
  1. Make sure the ignition key is OFF.
  2. Disconnect the air control valve.
  3. Use an ohmmeter to measure the resistance between the terminals of the valve solenoid. NOTE: Due to the diode in the solenoid, place the ohmmeter positive lead on the VPWR pin and the negative lead on the ISC pin.
  4. If the resistance is not 7–13 ohms, replace the air control valve.
---
REMOVAL & INSTALLATION Fig. 1: Idle air control valve mounting — 4.9L engine version shown, others similar 88484g10.gif
  1. Disconnect the negative battery cable.
  2. Disconnect the engine wiring to the IAC sensor.
  3. Remove the two retaining screws for the valve.
  4. Remove the IAC valve and discard of the old gasket. Fig. 2: Disengage the idle air control solenoid electrical connection 88485p12.jpg
    Fig. 3: Loosen the idle control solenoid retaining screws 88484p08.jpg
    Fig. 4: Remove the idle air control solenoid from the throttle body 88484p09.jpg
    To install:
  5. Clean the area of old gasket material.
  6. Using a new gasket, attach the IAC valve to the engine. Tighten the retaining screws to 71–102 inch lbs. (8–12 Nm).
  7. Connect the IAC valve wiring to the unit.
  8. Connect the negative battery cable.
prev.gif next.gif

Aug 01, 2010 | 1990 Ford Econoline

1 Answer

Vehicle serges while idling


petrol or diesel ? if petrol maybe idle speed control vale needs a clean out .

diesel possible air ingress when did it last have a new fuel filter ? or egr valve may need cleaning out .

Dec 07, 2009 | 2004 Ford Expedition

2 Answers

Replacing the control idle valve


All I had to do was clean mine and put it back They are expensive It has worked for 2 years after the cleaning

Mar 06, 2009 | 2001 Cadillac DeVille

2 Answers

High idle speed on 1987 ford F150


it may be this or the ( pcv valve ) pcv get clogged alot on old fords.The idle air control valve (IAC) control the engine idle speed and dashpot functions. The valve is located on the throttlebody . This valve allows air to bypass the throttle plate. The amount of air is determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal.

TESTING
  1. Make sure the ignition key is OFF.
  2. Disconnect the air control valve.
  3. Use an ohmmeter to measure the resistance between the terminals of the valve solenoid.
Due to the diode in the solenoid, place the ohmmeter positive lead on the VPWR pin and the negative lead on the ISC pin.
  1. If the resistance is not 7-13 ohms replace the air control valve.

Feb 18, 2009 | 1987 Ford F 150

Not finding what you are looking for?
1996 Ford F250 Crew Cab Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...