Question about 2003 Isuzu Rodeo

1 Answer

Was in accident and wheel was hit and bent and a part that holds the wheel was pushed back .

I was in accident and wheel was hit and bent and a part that holds the wheel was pushed back and I was told it need to be welded back to where it belongs...any ideas?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Can you weld? If not, bite the bullet and take it in for the repair. It's worth your life, isn't it?

Posted on May 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

06 liberty,ditched it think I have pushed my sub frame back 1/4 of an inch on drivers side.wondering if I can replace whole sub frame?

Time to file a claim with your insurance company. They types of accidents usually run well into the $1,500-$3,000 range.

Oct 11, 2017 | Cars & Trucks

1 Answer

I have a bent rear passenger side tire due to an accident, how do I fix it?

sounds like a hard hit ur problems can be an accumulation of one or more of the following bent rim --,bent and or broken hub,-- spindle bent or broken,shock,strut bent,broken--unibody [frame]bent ---u will have to remove wheel and look at the parts and see which is damaged also open trunk and look at the floor for bends and wrinkles also look at rear from back and look at the body for straightness unless u have a straightener for the unibody to fix body and or frame should be done by shop that is trained in repairs r the parts which ever part or parts need to be replaced they are all bolt in only worry would be replacing the strut if ur chevy came with that option most had a shock

May 21, 2012 | 2000 Chevrolet Cavalier

1 Answer

Having noises from passenger wheel my bf hit a curb and now it sounds funny he replaced the bent rim and the brakes and the wheels but it still makes the same noise

he may have bent the backing plate on inner side of wheel,tell him to remove that wheel and look at the metal plate behind the brakes,try spinning the wheel this will tell him where he needs to bend that plate back out. with a straight screwdriver, insert inbetween the brake rotor and push that backing plate away fro the brake rotor. this should take care of the scraping noise. thank you for choosing please rate my solution if i've been of service,thanks

Dec 30, 2010 | 2000 Hyundai Sonata

1 Answer

I hit a curb and the front driver side wheel is pushed back, what could be bent / wrong

Could be your lower/upper control arms or the torsion bar on your car that's bent, allowing the wheel to move back as you described.

Dec 14, 2010 | 2005 Kia Optima

2 Answers

Took for allinement was told could not do because pass side wheel was pushed back 1.5 inches

Something is bent. The alignment shop should have told you what was bent. Could be lower control arm, spindle, strut, ect.

Dec 30, 2009 | 2000 Plymouth Neon

1 Answer

Front diff been pushed back to far

Are you sure that your frame is not bent????? This will throw everything out of alliement. You will have to go from wheel to wheel and pull measurements like and X from side to side. fine the center point of the car and go from there. But it would be easer if you would put it on a frame machine!!!!!

Feb 07, 2009 | Toyota Land Cruiser Cars & Trucks

1 Answer


It sounds like you also will need a wheel bearing on that same wheel. ... Thanks Dan

Jul 10, 2008 | 2005 Dodge Stratus

1 Answer

Transmission problem

most likely you have a bad wheel bearing. It is very comen for a wheel bearing to go bad after an accident.

Jun 24, 2008 | 2004 Nissan Maxima

Not finding what you are looking for?
2003 Isuzu Rodeo Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides