Question about 1999 Chevrolet Silverado 1500

Open Question

Oil leak at oil filter housing replaced gasket to motor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: oil leak

front crank seal

Posted on Jul 29, 2008

Ad
  • 52 Answers

SOURCE: 1992 chevy siverado pickup 350 engine,I have a oil

you definately should check the oil pressure switch its probobly above or to the side of the oil filter and can make it look as if the filter is leaking,it will be threaded into the engnine itself and will have a connector on the top of it most likely with only 2 wires going to it

Posted on Apr 25, 2009

  • 86 Answers

SOURCE: oil leak 2002 trailblazer

if you think the filter gasket is leaking take filter off check for double gasket if it is replace the oil filter and take off 2nd gasket.

Posted on Aug 23, 2009

theautoguy
  • 69 Answers

SOURCE: my 1994 camaro w/ 3.4L engine has an oil leak in

This is most likely a leak from your rear main seal. It happens and can be a pain to replace if you're a DYI kinda person without the nec. equipment.

  1. Raise and safely support the vehicle with jackstands.
  2. Remove the transmission.
  3. If equipped with a manual transmission, remove the clutch and pressure plate.
  4. Remove the flywheel assembly.
  5. Using a suitable prytool, carefully pry the old seal out.
6. Inspect the crankshaft for nicks or burrs, correct as required.
88143g59.gif Crankshaft rear main seal - 5.7L engine

To install:
  1. Clean the area and coat the seal with engine oil. Install the seal onto tool J-34686 for 3.4L engines, J 41349 for 3.8L engines or J 35621 for 5.7L engines.
  2. Install the tool (with the seal mounted to it) onto the rear of the crankshaft. Tighten the screws snugly to be sure the seal will be installed squarely over the crankshaft.
88143g60.gif Exploded view of the rear main seal installation - 3.4L engine
Click to Enlarge

  1. Tighten the wing nut on the installation tool until it bottoms out.
  2. Remove the tool from the crankshaft or rear oil seal housing, as applicable.
88143g61.gif Rear main seal and installation tool - 3.8L engine
Click to Enlarge
88143g62.gif After position the seal on the tool, install it to the crankshaft housing

  1. Install the flywheel.
  2. If equipped with a manual transmission, install the clutch and pressure plate.
  3. Install the transmission.
  4. Check the fluid levels, start the engine and check for leaks.

Posted on Dec 30, 2009

  • 14036 Answers

SOURCE: it leaks oil bad i

REPLACE OIL FILTER.IT ALREADY HAS A RUBBER SEAL ON IT.REMOVE THE OLD OIL FILTER.TAKE NEW OIL FILTER FILL HALF WAY OR CLOSE TO TOP WITH NEW ENGINE OIL.RUB SOME OIL ON NEW OIL FILTER SEAL AND HAND TIGHTEN IT.IF HARD TO REACH PLACE JUST SNUG TIGHTEN WITH OIL FILTER WRENCH.DONT OVER TIGHTEN YOU CAN CUT DAMAGE OIL FILTER SEAL.WHEN YOU CRANK ENGINE CHECK FOR LEAKS AROUND OIL FILTER.

Posted on Nov 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 town car has leaking oil filter housing, what is necessary to fix and what the entire job will cost


it could be a simple replacement of the oil filter, remove the extra oil filter gasket left on when the filter was changed
excessive tightening of the filter
or replacement of the gasket for the housing mount
until you know exactly what is causing the leak , the cost cannot be calculated

Dec 30, 2016 | Cars & Trucks

1 Answer

Oil leak


is it leaking from top of filter -remove filter and check o-ring for damage and check housing for old o-ring[double gasket it happens] if good check housing for cracks and that gasket is good and bolts are tight -also check the pan gasket and bolts are good

Apr 30, 2013 | 2004 Chevrolet Blazer

1 Answer

Determine if it is the bolts or gasket on a oil filter housing leaking oil from it on a 1993 lincoln mark 8


Surely if you clean the area & start the car,
you will see the leaking area

No reason the oil filter gasket would leak
so remove the adapter & replace any gasket there

Mar 08, 2013 | Cars & Trucks

1 Answer

I'm driving a 2000 chv. Blazer, two wheel drive.


CHANGE THE GASKET FOR THE OIL FILTER HOUSING

Nov 27, 2012 | Cars & Trucks

2 Answers

Oil leaking from oil filter adaptor


i gotta 1950 ford coupe leaking oil out the oil filter housing and i can't find any solutions my gaskets are brand new anybody out there kno what my problem is then please tell me

Mar 22, 2011 | Chevrolet Equinox Cars & Trucks

3 Answers

Oil is leaking from where the oil filter is screwed into... is this the oil pump? is it difficult to replace?


Oil pump?

Your filter is leaking, check it out.

Can only be the adapter or the filter gasket

Feb 19, 2011 | 2005 Chrysler Town & Country

1 Answer

Replaced rear main seals and oil pressure sending on a 2000 z71


Check the oil filter housing and the cooler lines at the housing. The oil filter housing gaskets are good for no more than 15k to 30k miles if your lucky. The lines at the housing are easy to strip out when you reinstall them so take your time if you do it yourself an once you are finished and ready to start the truck, let it run for about 15 minutes and constantly check the area for leaks prior to road testing the vehicle.




May 12, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Started leaking oil apparently from top end near oil filter housing ,have replaced ring gasket every oil chnge. still unable to find leak. car has 110,000 km,meticuasly maintained any probables would be...


You will need to clean the area very well and watch for the leak while it's running. Most common leak cause is accidental double gasketing, where the old gasket remained on the filter pad and the new one was installed on top of it. i have also seen (but rarely) an oil filter with a defect in the casing. If your filter is mounted to an extension housing on the block, the gasket there can also leak.
You need to look though. 'Can't fix it if you don't know what it is!!!

Apr 11, 2010 | 2005 Chevrolet Cavalier

2 Answers

1992 chevy siverado pickup 350 engine,I have a oil leak in the side of my motor around the area of the oil filter,but it's not the oil filter and i replaced the valve cover gaskets


you definately should check the oil pressure switch its probobly above or to the side of the oil filter and can make it look as if the filter is leaking,it will be threaded into the engnine itself and will have a connector on the top of it most likely with only 2 wires going to it

Apr 25, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Oil Leak


there is a gasket on the oil filter .... upon removing the old filter you have to make sure that the old gasket came off .....if not then it stayed stuck in the filter housing . if the old gasket is there , all you have to do is pull it off with pliers !!!

Mar 25, 2009 | 1991 Chevrolet Astro Extended

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...