Question about 2006 Chevrolet Aveo

Open Question

THROTTLE/PEDAL POSITION SENSOR/SWITCH FOR AVEO

ENGINE LIGTH ON AND OFF

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: 2006 Chevy Aveo - Accelerator Pedal position Sensor - Parts

I hate to be negative but there is not a big aftermarket for your car, try googling it, if you get nothing chevy may be the way to go.

Posted on Mar 16, 2009

Ad
  • 18 Answers

SOURCE: i have a 2006 chevy

You do not have a TPS in your car.. I too have a 2006 ChevyAveo.. We have 2 TPS's located inside our Throttle body.. I had the same problem. I have completely replace the throttle body. IT fixed the problem, but when it gets dirty i have to clean it with carberator cleaner. if you clean it don't spray it into it because you ruin the sensors.. BTW you better have small hands to replace the throttle body, i have to use my camera phone to locate he bolts.

Posted on Aug 14, 2010

  • 4340 Answers

SOURCE: '06 chevy aveo vacuum leak at the intake manifold.

Proper resealing and problem resolution (warpage, etc.) cannot be done without removing and inspecting...
TPI sensors are problems on many cars, not a huge deal....

Posted on Sep 11, 2010

jturcotte
  • 8273 Answers

SOURCE: I have a 2007 Chevy

If it is a code P0226 I would not consider it a safety issue.


Throttle position (TP) sensor C/accelerator pedal

position (APP) sensor ? - range/performance problem


Possible Causes: Accelerator cable adjustment, TP/APP sensor

Throttle position (TP) switch C/accelerator pedal position

(APP) switch ? - range/performance problem
Accelerator cable adjustment, TP/APP switch

This might only be an adjustment issue--make sure the throttle cable isn't so tight that the throttle cannot fully close.
If the cable is OK, it is probably the accelerator position sensor under the pedal.
There are procedures for testing the unit that I will paste below if you care to try them.

If you just want a shop to fix it, the part is about $50 and labor should only be 30 minutes.


Operation The sensor is made up of the two individual sensors within a single housing. Each sensor has a unique functionality to determine pedal position. The APP system along with the Powertrain Control Module (PCM) is used to calculate and control the amount of acceleration and deceleration through fuel injector control.


Removal & Installation

  1. Remove the driver-s side knee bolster.
  2. Push down on the small tab and disengage the electrical connector.
  3. Remove the pedal bolts and remove the pedal and sensor assembly.
  4. Installation is the reverse of removal.

    5bcaece.gif

Fig. APP sensor mounting
Testing

  1. Install a 3 amp fused jumper wire between the 5-volt reference terminal of the APP sensor and 5 volts. Install a jumper wire between the low reference terminal and a ground.
  2. Sweep the sensor through the entire range while monitoring the voltage between the signal terminal and the low reference terminal with a digital multimeter. The voltage should vary between 0.30-4.98 volts without any spikes or dropouts.
  3. If the voltage is not within the specified range or is erratic, replace the accelerator pedal assembly.

Posted on Oct 06, 2010

seddy29732
  • 147 Answers

SOURCE: How do you replace a throttle position sensor on a

seddy29732_0.jpgThis is a picture of your throttle position sensor. It is located on the throttle body, where the air inlet tube enters the intake manifold. Simply unplug the wires, remove the bolts holding it in place, and replace it with the new unit. Hope this helps!

Posted on Jun 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 sta fe hyundai give code 121


P0121 HYUNDAI - Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance

Possible causes - Faulty throttle position sensor - Throttle position sensor harness is open or shorted - Throttle position sensor circuit poor electrical connection - Faulty Engine Control Module (ECM) What does this mean? When is the code detected? Malfunction is detected when an excessively low or high voltage from the sensor is sent to ECM. Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P0121 Hyundai Description The throttle position sensor (TPS) responds to the accelerator pedal movement. This sensor is a kind of potentiometer which transforms the throttle position into output voltage, and emits the voltage signal to the Engine Control Module (ECM). In addition, the sensor detects the opening and closing speed of the throttle valve and feeds the voltage signal to the ECM. Idle position of the throttle valve is determined by the ECM receiving the signal from the throttle position sensor. This sensor controls engine operation such as fuel cut. On the other hand, the Wide open and closed throttle position switch, which is built into the throttle position sensor unit, is not used for engine control.

Nov 20, 2016 | Hyundai Cars & Trucks

2 Answers

Po 122 problem light on had changed sensor problem not fixed trans not shifting right horrible jurks when it shifts.


P0122 is TPS signal low, which could mean you have a bad TPS, or a fault in the wiring or connector. I suspect a bad Throttle Position Sensor.

Apr 08, 2015 | 2000 Subaru Outback

1 Answer

How to fix p1121 code in dicor 1.4 l disel


P0120 Throttle/Pedal Position Sensor/Switch A -Circuit Malfunction
P0121 Throttle/Pedal Position Sensor/Switch A -Circuit Range/Performance Problem
P0122 Throttle/Pedal Position Sensor/Switch A -Circuit Low Input

,try changing the throttle pedal switch/mechanism on the floor in the cabin

Aug 05, 2014 | Tata Indica Cars & Trucks

1 Answer

2006 aveo throttle body issues


What engine does it have ? Could have come with 5 different ones . If it has the 1.6 L engine . has electronic throttle control.
The throttle actuator control (TAC) system is used to improve emissions, fuel economy, and driveability. The TAC system eliminates the mechanical link between the accelerator pedal and the throttle plate. The TAC system eliminates the need for a cruise control module and idle air control motor. The following is a list of TAC system components:
• The accelerator pedal assembly includes the following components:
- The accelerator pedal
- The accelerator pedal position (APP) sensor 1
- The APP sensor 2
• The throttle body assembly includes the following components:
- The throttle position (TP) sensor 1
- The TP sensor 2
- The throttle actuator motor
- The throttle plate
• The engine control module (ECM

Check engine light lit ?

Aug 26, 2017 | 2006 Chevrolet Aveo

1 Answer

P2106 P2110 P2135 P1516


Here is what meens those codes:

P2106
Throttle Actuator Control System - Forced Limited Power

P2110
Throttle Actuator Control System - Forced Limited RPM

P2135
Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation

P1516
Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance

I beleive that there is, specifically for chevrolet aveo 2006 a technician service bulletins.

You should have it checked at gm dealer!!!

ask for
TSB Number: SB-08-06-04-004
TSB Number: 08-06-04-023

Jan 27, 2014 | 2006 Chevrolet Aveo

1 Answer

Is the code P2135 covered under warranty for a 2007 Chevy Aveo?


P2135 Throttle/Pedal Position Sensor/Switch "A" /"B" Voltage Correlation, that's the code, you'd have to call the dealer to see if that's covered in the warranty

Aug 26, 2011 | 2007 Chevrolet Aveo 5 Hatchback

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

4 Answers

Chevy aveo error codes. I have a check engine light on.code p2135


P2135 Throttle Position Sensor (TPS) Property Malfunction, remember this is not a car that is built by GM it is a Korean import.

Jun 07, 2010 | 2004 Chevrolet Aveo

1 Answer

Code p2120 and P2125 on GMC Yukon 5.3 2006 with low engine power message. can you please tell me whats that .


OBD-II code P2120 What does it mean? Throttle/Pedal Position Sensor/Switch "D" Circuit

Poooooooooo2125
ThrottlP2125
ThrP2125
Throttle/Pedal Position Sensor/Switch "E"ottle/Pedal Position Sensor/Switch "E"e/Pedal Position Sensor/Switch "E"

May 27, 2010 | 2006 GMC Yukon

Not finding what you are looking for?
2006 Chevrolet Aveo Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...