Question about 1997 Honda Passport
I'm trying to fix my window but to get to it I need to take the inner door panel off. I've already taken off the first panel. I need help!!
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
There is a metal fitting bolt close to the bottom of the transmission. You can unscrew that out and if transmission fluid comes out it's good. If this doesn't occur you'll have to get a pump and pump transmission fluid in it. This is the easiest with a lift of course. Don't you hate stupid Japanese ideas. Good luck man
Posted on Jan 14, 2009
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
Turn the window handle to where you can see a small 1/2" slot rt at its base where it meets the panel.you'll notice a small brass v shaped clip,you'll need hooked pick or something simular to hook this clip and pull it out of its slot,this release's window crank handle. Once this is off the rest of panel is held on by plastic panel clips that pull loose by pulling panel outwards from door ,and also by a few various screws. once panel is off temp. slide window crank back on and crank window all the way up. You then should have clear view of outer door handle. Handle has two rods attached to it,one for lock assy., one for latch release.This is the one you'll be looking at.Most likely you will find rod has came loose due to broken retainer clip at handle,or casting on handle itself has broken off.If clip is broke you can buy new clip at dealer or at some autoparts outlets,replace and reattach rod(make sure rod locks into place).If handle casting is broke will need handle replaced.It is held in place by two 10mm bolts,two rods preeviously mentioned. If handle is body color matched will need color code(on door jam sticker)to order handle from dealer to match.Lock assy will need to be transfered to new handle,it is held in by two spring clips.You notice two holes one on each side of lock,you will need to push release clips inwards through each hole to release lock and slide it out.to install just push down into newhandlle until clips engage. Let me know if you run into problems. Good luck and if this was able to help you please leave me some positive feedback. Thanks and good luck, Joel
Posted on Oct 12, 2009
On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle
Posted on Nov 05, 2009
Tips for a great answer:
Oct 30, 2015 | 1996 Honda Passport
Oct 29, 2015 | 1996 Honda Passport
Mar 23, 2015 | 2001 Honda Passport
Sep 08, 2011 | 1997 Honda Passport
Jun 03, 2010 | 1994 Honda Passport
Sep 10, 2009 | 1997 Honda Accord
Jul 07, 2009 | 1997 Honda Civic
Jun 17, 2008 | 1996 Honda Passport
22 people viewed this question
Usually answered in minutes!