Question about GMC Cars & Trucks

Open Question

Headlight diagram 2004 gmc pickup high beam on driver side won't work replaced bulb

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: headlight bulb out

pop the hood take the plastic cover off it should have about 6 clips then unbolt the whole light from the car should be 2-3 screws and pull it out once u do that u might need to unscrew the plastic cover of the back to get to the wiring harness them u can change the bulb and reasmble

Posted on Apr 14, 2009

  • 12 Answers

SOURCE: high beam headlight does not work properly

it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!

Posted on Jul 13, 2009

  • 1 Answer

SOURCE: Toyota Sienna 2004 Headlight Problem

If you have the HID bulbs, and there is moisture in the bottom of the assembly, the high voltage box at the bottom will not work. this requires removing the whole headlamp, removing the circuit board from the bottom and drying out. I have done mine twice before finally finding how water was getting in at the top seam of the lamp assembly. You will have to dis-assemble part of the wheel well and bumper cover to gain access to all the mounting bolts. Best of luck

Posted on May 02, 2010

  • 1 Answer

SOURCE: Audi A4 2002 Low beams & Right front turn signal stopped working

but on 2002 A4, F20 and F21 are empty! Does anyone has an idea where the headlight fuses located?

Posted on Jun 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

1 Answer

Driver side brights not working from short?


check for broken ground wire or bulb filaments crossed in the fixture..

Dec 27, 2013 | 1998 GMC Jimmy

1 Answer

My low beam headlights won't turn on in 2004 gmc envoy


It's the headlamp relay #46. If you want to test it, swap it out with the cooling fan relay #45 and see if your headlights work. If they do you know this is the fix. Found the solution online a couple of years ago and it was spot-on. The part was $45 at autozone at the time.

Aug 12, 2012 | 2004 GMC Envoy

1 Answer

Need to replace low beam bulbs in 2004 GMC envoy. Help?


Lift hood, at top of each headlight assembly look for two L-shaped tabs. Pull these tabs straight up, this will release the headlight assembly. Lift assembly forward to gain access to rear of assembly. There two rubber caps, the top one is for access to the low beam and the bottom for the high beam bulbs. Remove the appropriate cap, grasp bulb socket and turn CCW to release. Unplug bulb from socket by releasing catch on side of socket, install new bulb, DO NOT touch bulb glass with fingers. Reverse steps to re-assemble.

Aug 26, 2010 | 2004 GMC Envoy

1 Answer

My passenger side low beam headlight is out. the driver side low beam headlight works fine. I replaced the bulb and the headlight still doesn't work. What should I look at next?


Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Dec 16, 2009 | 2004 Hyundai Santa Fe

2 Answers

One high beam works one doesn't, gauge cluster does not light up


you say you replaced both bulbs, you mean right and left or both the high beam and the low beam on left side?could be a bad ground for the left headlight. there should be some ground wires there near the headlight, LF corner under hood. without a wiring diagram here at home,I am not much help.

Sep 26, 2009 | 2000 Honda Accord

1 Answer

One headlight not working on 2004 Ford Escape


sounds like the socket for the bulb is bad.

Jan 12, 2009 | 2004 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...