Question about 2003 Toyota Highlander

Open Question

Low beam fuse

Where is the fuse for the low beam lights

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 79865 Answers

SOURCE: The right low beam light

this is not a fuse problem, it is the head light switch that changes from high to low beam most you need to rent our buy a steering wheel puller to remove the wheel and the then the steering column cover, always disconnect the negative battery cable before starting work as the Airbag is a explosive device.
to remove the steering wheel go to the link for a PDF of procedure, please note the link is for a 2001 but also applies to 03 models as well.
http://ww2.justanswer.com/uploads/JHoop/2010-07-24_164810_1.pdf

next remove the steering column cover and old combination switch, a link for that is below as well.
http://ww2.justanswer.com/uploads/JHoop/2010-07-24_153458_1.pdf

Posted on Oct 10, 2010

Ad
  • 2 Answers

SOURCE: Daytime Running Lights Inoperative 2002 Toyota Camry

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."


2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]


My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

Posted on Jan 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power to right side (PS) headlight low beam plug socket, new bulb, fuse is good. High beam works, blinker works, park light works. just no low beam and doesn't register any voltage on volt meter.


check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

Jan 30, 2014 | Cars & Trucks

1 Answer

2007 nissan quest low beam lights fuse


You should have a low beam relay that powers the fuse for each side. If both sides are out chances are the relay is at fault. The relay and fuses should be in the fuse box near the battery.
Check your owners manual for details.

Jul 11, 2013 | Cars & Trucks

2 Answers

No low beam lights but have high beam lights


check the light globe as a lot of cars have two filaments in the halogen globe. One for low beam and one high beam filament.
You could get a 12v probe and then pull of the light plug and see if low beam bul is getting 12 volts when lights on low beam.

Oct 12, 2017 | 2003 Land Rover Freelander

1 Answer

2005 Dodge caravan. The Headlights are not staying on. When we turn the switch, sometimes they come on, sometimes they do not. It's getting worse.


Hello, on the van you have a high beam fuse and relay. On the low beam you also have a fuse and relay. Check the fuse/relay panel for a blown fuse controlling the low beam lights. If you do not find a blown fuse have some one to turn the key on and turn on the high beam lights. During this time locate the low beam headlight relay and place your finger on top of relay, have the other person to switch from high beam to low beam lights. You should feel a click in the relay when they make the switch from high to low beam. If not replace the relay and the problem should go away. Hope this will help you.

Thanks

Aug 14, 2010 | 2005 Dodge Caravan

3 Answers

Low beam not working but high beam is-Pontiac Vibe 2005


I have heard it could be the Daylight Running Light module located under the dash above the brake pedal. The module controls both the daytime running lights and the low beam lights. The high beams are independent of this module.

I have the same problem. I am trying to buy a new module.

Jan 15, 2010 | 2006 Pontiac Vibe

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

Low Beam headlights out on Vovlo XC90


faulty light switch or light control module

Dec 05, 2017 | 2001 Volvo S40

4 Answers

Low beam headlights do not work, but high beam headlights do


Clyde,

I've been troubleshooting this same problem on a different vehicle this week, and I can give you the steps I'd take.

1. If both sides went out at the same time, the problem is *NOT* likely to be the bulbs.

2. Check the fuses to see if both low beam lights are on the same fuse. Many cars have one fuse for low beam and another for high beam, so both lights out at the same time typically means fuse blown.

3. If the headlights are OK and the fuses are OK, then the problem is *LIKELY* the headlight switch. In my case, AutoZone has one and it can be installed easily; but in your case, that may not be as simple.

Please post your findings or comments.

Jul 16, 2008 | 1991 Nissan Pickup

Not finding what you are looking for?
2003 Toyota Highlander Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...