Question about 2005 Mazda 3

1 Answer

Fuel pump removal in a 2005 mazda 6 4 cylinder

How do you remove the ring holding the fuel pump in

Posted by on

  • yadayada
    yadayada May 11, 2010

    u use a brass ( no sparks) drift punch and a hammer to drive it loose.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 205 Answers

You have to use a screw driver and hammer to tap it to the left until the tabs line up with the notches on the ring.

Posted on May 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump driver module




  1. Open Gas Cap. Ensure no open flames or Heated objects are nearby. Relieve the by loosening/disconnecting the fuel lines. Make sure you have a container to catch the fuel. Disconnect the battery Negative/ground cable. Lift the Left Hand rear seat cushion. It is necessary to lift the access cover on the floor scuff plate to access one of the pin-type retainers. Pull the the carpet aside. Remove the screws and the fuel pump module access cover. Disconnect the Fuel pump electrical wire connectors. Disconnect the fuel and vapor lines from the Fuel Tank. This has a quick release coupling.Rotate the lock ring counterclockwise and remove. Handle the fuel pump module must be handled carefully to avoid damage to the float arm and filter. Some fuel will remain in the fuel pump module after draining the Fuel Tank. Carefully drain the fuel pump module into a suitable container. Prior to completely removing the fuel pump, position it aside and using a suitable fuel recovery system, drain the Fuel Tank..



To release the bottom-mounted fuel pump module, reach into the fuel pump module opening and squeeze the retainer tabs or the pump module housing and pull upward. Remove the fuel pump module.



Be careful that no foreign material fall into the tank. Remove and discard the fuel pump module O-ring seal, making sure the mounting area is clean and free from foreign material.






  • When installing the fuel pump module, make sure to align the locator tabs on the Fuel Tank mounting flange.


  • When installing the fuel pump module locking ring, hold the O-ring while turning the locking ring until it stops against the retainer tabs.To install, reverse the removal procedure.




  • Start the engine and visually inspect for leaks.


  • Mazda Tribute Fuel Pump, In-Tank, New, Electric


    $88.07List Price $103.92Save $15.85Availability: In Stock

    SPECTRA PREMIUM FUEL PUMP
    $290.29List Price $342.54Save $52.25Availability: In StockNUIE0Q


    AIRTEX FUEL PUMP MODULE ASSEMBLYAirtex Fuel Pump is developed with the latest technological advancements in fuel delivery systems and not only complies with OE specifications but also improves upon fuel delivery.

Aug 19, 2013 | 2005 Mazda Tribute 3.0s

1 Answer

2005 silverado hot to replace fuel pump asssembly


Hello: , remove the lock ring holding the fuel pump module in the top of the tank and remove the fuel pump module being careful not to bend/break the fuel level sender float assembly. To do the above you have to remove the gas tank from the truck.

Jan 13, 2011 | 2005 Chevrolet Silverado

1 Answer

I cant get the cap off of my gas tank to take the fuel pump out, how do I get the fuel pump out?


Relieve the fuel pressure at the pump switch located in the passenger compartment under the carpet of the transmission hump on the passenger side. Remove the fuel tank. Turn the lock ring counterclockwise until it's loose and remove the lock ring. Pull the fuel pump/sending unit from the tank being careful not to bend the arm for the sending unit float. Discard the old lock ring seal. Installation is reverse of removal with the following additions: (a)Apply a coat of heavy grease to the new lock ring seal to hold it in place during assembly. Install the seal in the lock ring groove. (b)Install the fuel sender/pump unit into the fuel tank so that the tabs of the unit are positioned into the slots in the fuel tank. Make sure to keep the seal in place during installation until the lock ring has been tightened properly. (c)Hold the fuel sender/pump unit in place, install and tighten the locking ring clockwise until the stop is against the retainer ring tab. - Mazda Pickups Repair Manual

hope this help

Dec 02, 2010 | 1994 Mazda 2WD B Series Pickup

1 Answer

How much does a fuel pump cost for a 2005 mazda 6 4 cylinder


i do not know but give these websites a try www.autozone.com and www.alldatadiy.com also check with Napa or Advance auto stores wish you the best of luck Michigan Man.

Sep 07, 2010 | 2005 Mazda 6

1 Answer

The fuel pump has ben taken apart


REMOVAL & INSTALLATION 2.3L 4-Cylinder and 2.8L 6-Cylinder Engines
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Raise and support the vehicle safely.
  4. Remove the fuel tank.
  5. Loosen the lock ring at the top of the fuel tank and remove the sending unit with the transfer pump attached. Note the direction of the float in the tank.
  6. Remove the transfer pump from the sending unit. To install:
  7. Install the transfer pump on the sending unit.
  8. Install the sending unit in the fuel tank and tighten the lock ring to specification. Do not overtighten the lock ring as the plastic threads on some fuel tanks are easily stripped.
  9. Install the fuel tank in the vehicle.
  10. Lower the vehicle.
  11. Connect the negative battery cable.
  12. Start the engine and check for leaks. Fig. 1: Fuel pump assembly for the 2.3L 4-cylinder engine 90955g07.gif
    Fig. 2: Fuel pump assembly for the 2.8L 6-cylinder engine 90955g17.gif
2.3L and 2.4L 5-Cylinder, and 2.9L 6-Cylinder Engines
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Tilt the rear seat forward and remove or fold back the trunk compartment carpet over the right-hand wheel well panel.
  4. Disconnect the fuel pump electrical connections. NOTE: Take note of the color markings on the hoses; colored tape should identify hose locations on the pump.
  5. Detach the quick-connect couplers for the fuel delivery and return hoses.
  6. Remove the pump unit by unscrewing the retaining nut using tool 999-5485 or equivalent.
  7. Lift the pump out carefully and remove the rubber seal. When lifting the pump out, do not grab the connections with pliers or any other sharp tools that might cause damage and result in fuel leakage. To install: WARNING
    Install the retaining nut while the pump is removed, otherwise the tank connection may swell and the nut will be difficult to install.
  8. Install a new dry seal, making sure that it is seated properly. Lubricate the top and outer side of the seal with petroleum jelly.
  9. Install the pump with the heater connection facing towards the right side of the vehicle.
  10. Install the fuel pump retaining nut and tighten it to 30 ft. lbs. (40 Nm) using tool 999-5484 or equivalent.
  11. Apply a small amount of petroleum jelly to the delivery and return hose ends and install them on the pump. The delivery line is marked with yellow tape, which should be matched to the yellow marked pump outlet. Make sure that the quick-connectors are properly seated on the pump.
  12. Connect the electrical connections, making sure that they are in the correct position. Install the panels and carpets.
  13. Connect the negative battery cable.
  14. Run the engine and check for leaks. Fig. 3: Remove the clips retaining the carpet . . . 90955p01.jpg
    Fig. 4: . . . to expose the fuel pump access cover 90955p03.jpg
    Fig. 5: The rear seats can be folded down from the inside, but this lever must be in the up position 90955p02.jpg
    Fig. 6: Release this lever from inside the car to lower the rear seats 90955p12.jpg
    Fig. 7: Remove the trim retaining bolt from the bottom of the panel 90955p04.jpg
    Fig. 8: Remove the seat back striker using a T30 Torx® bit 90955p05.jpg
    Fig. 9: Carefully push the trim back . . . 90955p06.jpg
    Fig. 10: . . . to access the fuel pump harness connections 90955p07.jpg
    Fig. 11: Remove the fuel pump access cover retaining bolts 90955p08.jpg
    Fig. 12: When the cover is removed, the fuel pump is visible 90955p09.jpg
    Fig. 13: Detach the quick-connect fittings . . . 90955p10.jpg
    Fig. 14: . . . and remove the fuel lines from the pump 90955p11.jpg
    Fig. 15: Use wrench 5485 or equivalent to remove the fuel pump retaining ring 90955g08.gif
    Fig. 16: After the retaining ring is removed, lift the pump out of the tank 90955g09.gif
prev.gif next.gif

Aug 01, 2010 | 1994 Volvo 940

1 Answer

Hello, I was just wondering how to change the fuel filter on a 2005 mazda 6 v6?


Mazda Car 2005-06 Repair Guide
Fuel Filter Removal & Installation

The fuel filter on most Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.

The filter on Mazda3 models is part of the fuel pump assembly.
The fuel filter is part of the pump assembly. Once the fuel pump is removed, remove the filter retainer and filter. refer to the fuel pump procedure or removal and installation.

Hope helps with this (remember rated this help) Good luck.

Jan 12, 2010 | 2005 Mazda 6

1 Answer

Fuel filter location/replacement My car is cutting out at 4000 RPM


2006 Mazda MX-5 Miata 2.0L MFI DOHC 4cyl
Mazda Car 2005-06 Repair Guide - Removal & Installation

The fuel filter on most Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.

The filter on Mazda3 models is part of the fuel pump assembly.

The fuel filter is part of the pump assembly. Once the fuel pump is removed, remove the filter retainer and filter. refer to the fuel pump procedure or removal and installation.

I hope help you. Good luck.

Oct 12, 2009 | 2006 Mazda Miata

1 Answer

2005 mazda 6 can't get the retaining ring on the fuel pump off. Bought fuel pump removal tool but it wont fit inside the space to remove it very well. thinking about cutting the bottom a little bit to make...


There are some suggestions on this problem, man. First thing first, a good chat at the local Mazda car dealer mechanics could be invaluable, as these guys could help you, or you could see a friendly mechanic elsewhere Alternatively, there are Mazda website dedicated to owners who repair their own cars and might post load of suggestions on how to do it yourself queries. Try them.

Sep 18, 2009 | 2005 Mazda 6

1 Answer

No gas going to 2005 mazda 6i


the fuel pump is a complete asm. that you can get from mazda we sell them every day. the way you get to it is to remove the back seat lower seat. you remove it and you will see a panel that once you remove it the top of the gas tank and fuel pump are visible. you will need a special tool to unscrew the hold down but after that it is very easy to change.

Aug 04, 2009 | 2005 Mazda 6

1 Answer

Changing fuel pump of Mazda 6 2005


Disconnecct battery. flip fuel pressure switch in trunk, raise car disconnect fuel lines,disconnect fuel pump level sending electrical unit, using a brass ppunch tap lock ring counteerclock wise until loose, remove unit from tank, would highly recommend you remove all the gas from the tank, bwefore atempting this. Good luck.

Jul 01, 2009 | 2005 Mazda 6

Not finding what you are looking for?
2005 Mazda 3 Logo

Related Topics:

1,716 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...