Question about Ford F-150

Open Question

Po codes 300 301 302 351 352 353

Truck running fine then all the sudden started misfiring and skipping had no power at all when put in gear but seamed to idle fine when in park but rough when given gas changed fuel filter first thought it was clogged but did not fix problem does this mean it has a bad coil

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 137 Answers

SOURCE: my explorer idles fine in park but skips and misses when under load

K the next thing to check is the throttle position sensor. It's probably going bad. The same thing happened to me on my 1995 F250 5.8L

Posted on Sep 16, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Losing power and skipping wont pull up an incline


How long since a tune-up? Any applicable trouble codes? Some of the national brand auto stores will check po codes for free.
If a cylinder misfire, hopefully the code will tell you which cylinder, then check spark--fuel--compression on that cylinder. If a po300 code, that is a fault that is common to all cylinders, not just one.

Jul 17, 2017 | Cars & Trucks

1 Answer

Trouble codes po 760, po 755, and po 134


Sounds like the oil level in the gearbox is low ,if it has a dipstick then start engine and chock wheels ,put in reverse with engine running and check oil level

Jan 04, 2014 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

Engine Code PO 300 and PO 316 came up when running diagnostic


P0300 is random multiple cylinder misfire and P0316 is misfires detected on start up. This is an ignition related issue. I would check the ignition system and tune up condition and proceed from there also if you have access to a sanner with live data capability check that you have and RPM reading when cranking the engine and the times it deosnt want to start this would indicate an issue with the crank sensor

Oct 24, 2012 | 2005 Ford Taurus

1 Answer

2002 saturn vue cylinder 1,3,5 misfiring when swapped coil pack it went away now cyl 2,6 misfiring.


having PO 304 = Misfire cylinder 4,PO 306 = Misfire cylinder 6, as I read above you have done the most. The thing that you have missed is to check whether the Catalytic Converter is faulty or not. To get an idea check whether you have a smell like rotten eggs at the end of the exhaust,you start having problems with cat and needs replacement. My advice before you go for a cat replacement is good to visit an MOT center and check your emissions and then you decide,

Aug 10, 2012 | Kia Rio Cars & Trucks

1 Answer

Car will skip right after starting , within two miles skip will stop and car runs fine. engine light on with code PO 316


P0316 can come on intermittently showing a crank/misfire detection in the engine system. Over time you will notice this fault get worse, especially in wet/damp weather. The fault is usually cause by water ingress into the coil areas above the spark plugs. You need to take the coils out, smear some vasaline ( or similar substance) around the rubber seals on the coil units and refit them, ensuring there is no water in/around the spark plug. If so blow the water out and dry this area. Hope this helps...vote for me.

Mar 12, 2011 | Ford Escape Cars & Trucks

1 Answer

1999 3.8L Ford windstar misfire


replace the EGR unit
put a can of injector cleaner in the tank
check the cat converter for blocking the exhaust system

Jun 02, 2017 | 1999 Ford Windstar

2 Answers

Code Po171, P0174 P0403 . Upon acceleration....truck is jumping. One code metioned Cyl 3 misfire


PO 171 & 174-are O2 Sensors Codes,forget them,just be sure their screwed in tight. Yes ,they will come loose.
PO303-is a bad COP Coil,on #3 cyl ,may be one issue,very common on all ford products
PO-403 -is EGR related.-That probably is shot, also.

Had all thoses and more, on my Lincoln Ls

A misfire will set many codes,that while not unrelated,are not your issuse. You need to understand the symptom,is not always what caused the codes,or not the cause of the problem.

May 09, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

At about 4000 RPM the check engine light flashes and there is hesitation. The read out says misfire in #3. I have a 2000 GMC Yukon, During regular speeds it is fine. There also seams to be a hesitation...


Your catylatic converter may be clogged if your loosing power or top speed is less than it was. You can check this when its running with a battery operated infared heat gauge. the temperature of the muffler should be around the same temp. as the catylatic converter.

Sep 24, 2009 | 2000 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...