Question about Cars & Trucks
Brake light in rear hatch burned out where do you locate to change blub?
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
4.2L Engine the thermostat and the neck where the hose goes on is one unit $25 at autozone
Posted on Dec 29, 2008
sounds like a fuse look under the dash panel for fuse cover look at the back of cover and check that fuseThanks for using fix ya Please rate my response thank you very much
Posted on Jan 31, 2009
one, five, three, six, two, four
The plastic intake should have this sequence molded into it somewhere, and even the corresponding cylinder numbers in front of their respective holes. Have fun, and thanks for posting on Fixya.com
Posted on Mar 20, 2009
SOURCE: I need to know how
It would be to hard to tell and show you over the computer.
The best and easiest way for you is to buy a Chilton manual for your car at the autoparts store. The book runs about $20
This book is a do-it-yourself bible. It will show you everything you need to know on how to do maintenance and repair on your vehicle.
Posted on Apr 13, 2009
don't need any special tools, standard sockets sets, "C" clams is a must unless your a He-Man and wrench set, plyer or needle nose will do. I assumed being 2003 your rotor never have been turn and i recommend every time you change your bakes is good idea to have your rotor turn. reason is it will make your pad last lot longer, removed any vibration and better even wear on the pad and eliminate any squealing although is not necessary to do so. make sure you get extra break fluid to bleed the brakes. get your self 5 feet long smallest vacum rubber hoses and a glass jar to bleed your brake fluid in. the rubber vacum hose you going to use to fit on to the bleeding nipple and run the other end of line to your the glass jar to save the brake fluid when you bleed the brakes. when removing caliper, check inspect make sure the rubber seals around your piston look good and not crack or deteriorated. before applying new pad make sure you open the bleed valve to reduce the pressure by turning the bleed nipple counter clockwise and leave it open attach that rubber hoses to the nipple because you going to press on the piston back into it housing with the "C" clamp in order for new pad to fit. becareful not to damage the rubber seals around the piston. its going to take lots of effort to push that piston back in so be a bare with it if needs to. once the pad is back in make sure you keep the reservoir full with brake fluid and then bleed the brake. two people is a good idea to do brake. one will do the pumping the brake and holding it down and other will bleed the nipple. I bleed it 2-3 time will do the job. good luck!
Posted on Jul 17, 2009
Tips for a great answer:
Jan 16, 2016 | 2002 Chevrolet Tahoe
Jul 29, 2011 | 2002 GMC Envoy
Try pulling the rear hatch panel and move the unlock mechanism with a screw driver to get it to open.
If that does Not work:
Check for broken wires in the liftgate boot. Test the liftgate module powers and ground on the 4 terminal connector: 12 volts on the Orange wires in terminals A and C, ground on the Black wire in terminal D. The liftgate module is located inside the gate.
Dec 31, 2010 | 2002 GMC Envoy
Mar 25, 2010 | 2004 GMC Envoy
Mar 12, 2010 | 2005 GMC Envoy Xl
Mar 19, 2009 | 2002 GMC Envoy
Jan 30, 2009 | 2004 GMC Envoy
51 people viewed this question
Usually answered in minutes!