Question about Kia Cars & Trucks

Open Question

Indicators stop flashing intermittently

Sometimes the indicators stop flashing after maybe 15 or 20 seconds. They just stay on. The next time I use them they are OK again for another 15or 20 seconds. It seems to be happening more frequently now. Can anyone help please? thank you

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: automatic tiptronic gearbox sometimes sticks

have you had any transmission services done yet? like a flush sounds like a sticking solenoid but very hard to say with out looking into it please rate -jeff

Posted on Sep 01, 2008

GasparMacari
  • 166 Answers

SOURCE: Vauxhall/Opel frontera indicators not working

thats a relay thats is not working propperly, must be replaced to fix the problem, just go to your dealiship and ask for a turn indicator relay for your model and ask your part sales man to show you where is located, if not...just follow that click...
have fun

Posted on Aug 21, 2009

  • 16 Answers

SOURCE: Fiat Stilo 1.9JTD power loss after 30k miles

Its the EGR valve. Had exactly the same problems on my old 1.9 JTD.

You can take it off and remove all the carbon crud thats built up inside but the problem WILL return unfortunately. Its a mechanical failure so no error codes will be shown for this fault. You can also block them off which will return all of your power but also possibly make it an MOT failure due to excess soot coming from the exhaust.

Posted on Oct 13, 2009

  • 1 Answer

SOURCE: diesel mondeo glow plug indicator keeps flashing when driven

Hi Shaunbarry, Have you been able to fix the problem changing the EGR valve?

Posted on Dec 27, 2009

  • 6982 Answers

SOURCE: driving down the road. steering

First, loosen your wheels and re-tighten in a star pattern using a torque wrench.(setting of around 70-75 foot lbs is good) If that does not help, check your ball joints. Especially the lowers as they have no provision for lubrication and do not last as long as they should.Track bar end at the chassis should be checked to make sure it's tight and that the bolt hole has not become oblong. Other than that, check all front end components for looseness. The steering stabilizer (sideways shock on steering linkage) is often blamed for that condition and though it can be damaged by it, it never is the cause. Last, in extreme cases where everything has been checked and proves to be good, you can have an alignment shop put a bit more caster in the settings. that causes it to want to go straight without wheel flutter.
I gave you recommendations in the order of importance. I've dealt with and cured this condition (called death wobble) on many many Jeeps. If you have any questions just ask!!!

Posted on Sep 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 PT Cruiser Limited Turbo, check engine light on and flashed various codes. P0882, P0714, P0700, P01603, P0551, P0100 and P0101. Can i do pin test?


Code 100 and 101 are for problems with the Mass air flow meter.
Have you checked it ?
You can pin test the computer but you may need a shop manual to get the wiring diagrams.

Nov 15, 2015 | Cars & Trucks

3 Answers

What part needs fixed when my turn signal blinker blinnks very fast and sometimes not at all.If I put pressure on the turn arm it will stop sometimes or clicking my high beams on or off sets it right


Flashing too fast means that at least one exterior bulb isn't working. IF its an intermittent problem, once bulb could not be making connection at times. next time its flashing fast, stop the car and look to see which bulb isn't working. Replace that bulb, clean the socket at the same time

Oct 07, 2014 | 2001 Toyota 4Runner

1 Answer

Ford airbag code 54


94+ AIR BAG DIAGNOSTIC TROUBLE CODES/CLEARING
Code Component/Fault Description

No Air Bag Indicator - Inoperative Indicator Circuit
Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor.
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 RH Radiator Primary Crash Sensor Feed/Return Circuit Open
42 LH Radiator Primary Crash Sensor Feed/Return Circuit Open
44 RH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
45 LH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
52 Intermittent or Repaired Lost Battery Feed
53 Intermittent or Repaired Air Bag Circuit Shorted to Ground
54 Intermittent or Repaired Primary Crash Sensor Circuit Shorted to Ground
61 Intermittent or Repaired Diagnostic Monitor Not Mounted to Vehicle Properly
62 Intermittent or Repaired Safing Sensor Output Circuit Shorted to Battery Voltage
63 Intermittent or Repaired Memory Clear Circuit Improperly Grounded
64 Intermittent or Repaired System Disarm Failure or Internal Diagnostic Monitor Fault
72 Intermittent or Repaired Driver Side Air Bag Circuit High Resistance or Open
73 Intermittent or Repaired Passenger Side Air Bag Circuit High Resistance or Open
74 Intermittent or Repaired Driver Side Air Bag Circuit Low Resistance or Shorted
75 Intermittent or Repaired Passenger Side Air Bag Circuit Low Resistance or Shorted
81 Intermittent or Repaired RH Radiator Primary Crash Sensor Feed/Return Circuit Open
82 Intermittent or Repaired LH Radiator Primary Crash Sensor Feed/Return Circuit Open
84 Intermittent or Repaired RH Radiator Primary Crash Sensor Not Mounted to Vehicle
85 Intermittent or Repaired LH Radiator Primary Crash Sensor Not Mounted to Vehicle
Rapid Continuous Flashing of Air Bag Indicator (No Diagnostic Trouble Code) Both Primary Crash Sensors Disconnected Assembly Plant Mode

TROUBLE CODE CLEARING

1. Follow the diagnostic procedures to service the fault condition flashing on the air bag indicator prior to code clearing.

2. Cycle the ignition switch to OFF and then to RUN.

3. Observe air bag indicator prove-out (six ? two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.

4. Locate the Diagnostic "Trouble Code Clear" Connector (grey connector). located underneath the glove compartment, left side (06010) containing Circuits 631 (T/R) and 57 (BK).

5. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.

6. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).

7. Release short on Circuit 631 (T/R) to Circuit 57 (BK). This short must be released within 25 seconds after the diagnostic monitor tone sounds.

Diagnostic trouble code is now cleared from memory. Next highest priority diagnostic trouble code stored (if one exists) will begin flashing.

The codes and clearing proceedure above are to be used as a guide, NO claims are implied as to the correctness or accuracy of either.

Sep 11, 2013 | Cars & Trucks

1 Answer

2006 citroen relay indicators have stopped working and now getting "batt" flashing any ideas ?


The battery light flashing is an indication of an intermittent short. The intermittancy seems to be caused by a "hung" relay or a partially welded relay that is not releasing its contacts. Try going to the relay and fuse box under the hood and pulling one relay at a time to see if the observed action stops. If it does, replace the faulty relay. If not go to the fuse box under the dashboard and do the saqme thing!

Jan 11, 2013 | Cars & Trucks

1 Answer

2005 honda odyssey homelink programming


If you just received your vehicle and have not trained any of the buttons in HomeLink before, you should erase any previously learned codes before training the first button. To do this, press and hold the two
outside buttons on the HomeLink Transceiver for about 20 seconds, or
until the red indicator flashes.
Release the buttons, then go to step 1.
If you are training the second or third buttons, go directly to step 1.

1. Unplug the garage door opener motor from the electrical outlet.
2. Hold the end of the garage door opener remote 2 to 5 inches from HomeLink. Make sure you are not blocking your view of the red indicator in HomeLink.
3. Press and hold the remote transmitter button and one of the HomeLink buttons at the same time.
If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indictor in HomeLink continues to flash slowly (does not flash rapidly), your remote transmitter may stop transmitting after a short time. Go to step 4.
4. Press and hold the remote transmitter button and one of the HomeLink buttons at the same
time. While continuing to hold the HomeLink button, press and release the remote transmitter button every 2 seconds. If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indicator in HomeLink continues to flash slowly (does not begin to flash rapidly), repeat steps 2 thru 4.
5. Plug in the garage door opener motor, then test the HomeLink button by pushing it for about 1
second. If the button works, programming is complete. If the button does not work go to step 6.
6. Push and hold the HomeLink button for a few seconds, then watch the red indicator on HomeLink.
If the indicator stays on or flashes slowly, repeat steps 2 thru 5. If the indicator flashes rapidly
for 2 seconds then stays on, you have a rolling code transmitter. Go “Training with a Rolling Code System”
7. two HomeLink buttons to operate any other compatible remotely controlled devices around your
home (lighting, automatic gate, security system, etc.).
Repeat these steps to train the other

Jan 05, 2010 | 2006 Honda Odyssey

1 Answer

My remote control no longer opens the doors even though the batteries have been renewed


Insert the ignition key and turn from position II (Ignition) to position 0 (off)
and back four times within three seconds. Remove the ignition key.
The locking control system is now in "learn mode" for the next 20 seconds the
red warning system LED stays on continuously to indicate this.
During the 20 seconds press one of the transmitter buttons. The remotes signal and
code number is learned by the locking module and is indicated by flashing the
warning system LED.
Wait until learn mode times out (20 seconds) or switch the ignition back to ON.

Jan 02, 2010 | 2000 Ford Focus

2 Answers

Everytime I change the fuse it burns out


Obviously your Flasher is defective or one of the Lamps is intermittent. Federal Law requires the Flasher to quit Flashing if a Bulb is Burned Out or the Circuit to either front or rear has an intermittent connection. Next time it Stays on check the Front Bulb for the side you are indicating a turn. If Both Front and Rear Bulbs are lit then replace the flasher. Flashers do wear out!

Fastest Robe

Oct 19, 2009 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Audi TT 2000 - radio and indicators


Hi Mate

I think I can help here.

You will find that there is a relay behind the hazard warning switch that is faulty. Change that relay and everthing should be fine.

Apr 30, 2009 | 2001 Audi TT

2 Answers

Air bag Indicator flashed and than stays on


If the only code 52 is flashing then system is ok and just needs to be cleared.Look behind the glove box and find the gray 2 wire connector.It will be on the left side behind the glove box and follow the proceedure below. Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ±two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic Service Connector located underneath the glove compartment containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (T/R) to Circuit 57 (BK). Diagnostic trouble code is now cleared from NVM. Next highest priority diagnostic trouble code stored in NVM (if one exists) will begin flashing

Mar 03, 2009 | 1994 Ford Mustang

1 Answer

Airbag flashes 10 times misses a flash then repeats


Try clearing the codes & see if it returns. I do not see a code fault 10. Starts at 12.

---------------------------------------------------------------------
Section 01-20B: Restraints, Passive — Supplemental Air Bag System 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual DIAGNOSIS AND TESTING Diagnostic Trouble Code Clearing Procedure to Clear Diagnostic Trouble Codes from Diagnostic Monitor Non-Volatile Random Access Memory.
Normal Operation
The air bag diagnostic monitor (14B056) continually checks the air bag system for readiness. When a fault condition is detected, the DTC associated with that fault is stored in the air bag diagnostic monitor's Non-Volatile Random Access Memory (NVRAM). After writing the DTC to NVRAM, the air bag diagnostic monitor signals the fault by flashing the appropriate diagnostic trouble code on the air bag indicator. The diagnostic trouble code written to NVRAM is permanently stored in the air bag diagnostic monitor until cleared by the diagnostic trouble code clearing procedure.
  • Upon each cycle of the ignition switch (11572) , the air bag diagnostic monitor checks for diagnostic trouble codes written in NVRAM. If any diagnostic trouble codes exist in NVRAM, the air bag diagnostic monitor will then check to see if these fault conditions are still present.
  • If the conditions of the diagnostic trouble code in NVRAM are still present, then the air bag diagnostic monitor will use the air bag indicator to flash out the diagnostic trouble code number that was written in memory.
  • If the conditions of the diagnostic trouble code are not still present (indicating an intermittent or serviced fault), the air bag diagnostic monitor will use the air bag indicator to flash out a DTC which is the sum of the diagnostic trouble code in NVRAM plus 40.
Example: Due to corrosion, high resistance develops on the driver side air bag circuit. The air bag diagnostic monitor stores a diagnostic trouble code 32 in NVRAM. Upon each cycle of the ignition switch , the air bag diagnostic monitor checks the resistance of the driver air bag circuit.
  • If the resistance is still high, the air bag diagnostic monitor causes the air bag indicator to flash out a DTC 32.
  • If the resistance falls within the normal range due to service or an intermittent condition, the air bag diagnostic monitor causes DTC 72 to be flashed on the air bag indicator.
Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVRAM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (TAN/RED STRIPE) to Circuit 57 (BLACK). This short must be released within 25 seconds after the diagnostic monitor tone sounds. Diagnostic trouble code is now cleared from NVRAM. Next highest priority diagnostic trouble code stored in NVRAM (if one exists) will begin flashing.

Feb 09, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...