Question about 2000 Isuzu Rodeo

1 Answer

Installing throttle positioning sensor

I need to know what to take off to get to the two screws holding in the TPS. It seems to be impossible to get to the back screw. I see two bolts for the pedal assembly, but wanted your advice first. Thanks

Posted by on

  • yadayada
    yadayada May 11, 2010

    look u do what ever it takes to get to the screw, most likely that means removing the throttle valve assembly, that is what I do.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,623 Answers

There are specialty tools that make removal a little easier, flex shafts. angle drive drivers...etc.
Not sure why you need to replace the TPS on the 3.2, but if it's for a trouble code repair this is rarely the problem.
Good luck...i hope this helps.

Posted on May 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have 1995 Chev S10 with a 2.2L. It stubles from stop bad. I have replaced fuel filters and tuned it up,no help.


Test the tps using procedure below.


Throttle Position Sensor (TPS)
The Throttle Position Sensor (TPS) is connected to the throttle shaft on the throttle body. It is a potentiometer with one end connected to 5 volts from the VCM and the other to ground. A third wire is connected to the VCM to measure the voltage from the TPS. As the throttle valve angle is changed (accelerator pedal moved), the output of the TPS also changes. At a closed throttle position, the output of the TPS is low (approximately 0.5 volts). As the throttle valve opens, the output increases so that, at wide-open throttle, the output voltage should be approximately 4.5 volts. By monitoring the output voltage from the TPS, the VCM can determine fuel delivery based on throttle valve angle (driver demand).

TESTING


See Figures 1, 2 and 3

Backprobe with a high impedance voltmeter at TPS ground terminal and 5 volt reference signal terminal.
With the key ON and engine off, the voltmeter reading should be approximately 5.0 volts.
If the voltage is not as specified, either the wiring to the TPS or the VCM may be faulty. Correct any wiring or VCM faults before continuing test.
Backprobe with a high impedance voltmeter at the TP signal terminal and the sensor ground terminal.
With the key ON and engine off and the throttle closed, the TPS voltage should be approximately 0.5-1.2 volts.
Verify that the TPS voltage increases or decreases smoothly as the throttle is opened or closed. Make sure to open and close the throttle very slowly in order to detect any abnormalities in the TPS voltage reading.
If the sensor voltage is not as specified, replace the sensor.


0996b43f8021e0ea-j1axptdruxmkgupulmd503d3-5-0.gif

Fig. Fig. 1: Common Throttle Position Sensor (TPS) wiring diagram (wire color, terminal identification/location may vary on certain models)



0996b43f80232a38-j1axptdruxmkgupulmd503d3-5-2.gif

Fig. Fig. 2: Using jumper wires and high impedance voltmeter, test between the sensor ground and reference terminals, the voltage should be approximately 5 volts




0996b43f80232a38-j1axptdruxmkgupulmd503d3-5-5.jpg

Fig. Fig. 3: Next test between the sensor signal and ground terminals, verify that the TPS voltage increases or decreases smoothly as the throttle is opened or closed.


REMOVAL & INSTALLATION

Except 1998-99 2.2L Engines
See Figure 4



0996b43f8021e0e9-j1axptdruxmkgupulmd503d3-5-9.gif


Fig. Fig. 4: Common Throttle Position Sensor (TPS)
Disconnect the negative battery cable and remove the air cleaner and if equipped, the gasket and bracket.
Disengage the electrical connector.
Unfasten the two TPS attaching screw assemblies.
Remove the TPS from the throttle body assembly.
Remove the TPS seal.

To install:
Install the TPS seal over the throttle shaft.
With the throttle valve closed, install the TPS on the throttle shaft.
Rotate it counterclockwise, to align the mounting holes.
Install the two TPS attaching screws.
Tighten the screws to 18 inch lbs. (2 Nm).
Engage the electrical connector.
If equipped, install the bracket and gasket air cleaner and gasket.Connect the negative battery cable.

1998-99 2.2L Engines
Disconnect the negative battery cable and remove the air cleaner outlet resonator.Remove the throttle body assembly.Unfasten the two TPS attaching screw assemblies.Remove the TPS from the throttle body assembly. To install:
With the throttle valve closed, install the TPS on the throttle body.Install the two TPS attaching screws. Tighten the screws to 27 inch lbs. (3 Nm).Install the throttle body.Install the air cleaner outlet resonator.Connect the negative battery cable.

Aug 20, 2017 | Cars & Trucks

1 Answer

Where's the idle screw on a 2002 Cadillac Deville


No screw - fully computer controlled. Also, there is no idle control sensor - just a throttle position sensor (TPS) and an idle air control (IAC) motor. If you are replacing the IAC, clean the throttle body ports VERY carefully using a recommended solvent.

Sep 16, 2014 | 2002 Cadillac Deville

1 Answer

How to replace the TPS.


no engine option stated, and is key fact to know here.
eg:
The 5.7L V8 engine does not use a separate Throttle Position Sensor (TPS) on the throttle body.

remove old TPS, and bolt on new.
its like 2 or 3 screws. no big deal.
but needs to be calibrated per fsm.
ill take a wild guess, 3.7L
3.7L Engine and 4.7.
  1. Remove air resonator tube at throttle body.
  2. Disconnect TPS electrical connector.
  3. Remove two TPS mounting screws.
  4. Remove TPS.
install
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.
  1. Install TPS and retaining screws.
  2. Tighten screws to 60 inch lbs. (7 Nm) torque.
  3. Connect TPS electrical connector to TPS.
  4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.
  5. Install air cleaner tube to throttle body.
some TPS need calibration
to see what yours needs, read the FSM
or at alldata.com
or here. I think all engines here, are TPS PCM autocalibrated.

read WJ car here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

May 24, 2014 | 2005 Jeep Grand Cherokee

1 Answer

Where is the thorttleposition sensor on 2001jeep cherokee


The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:

selectachapter.gif

Cherokee, Grand Cherokee, 1999-2005
Throttle Position Sensor

Print


Operation

The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:


Ignition timing advance Fuel injection pulse-width Idle (learned value or minimum TPS) Off-idle (0.06 volt) Wide Open Throttle (WOT) open loop (2.608 volts above learned idle voltage) Deceleration fuel lean out Fuel cutoff during cranking at WOT (2.608 volts above learned idle voltage) A/C WOT cutoff (certain automatic transmissions only)


Removal & Installation

3.7L & 4.0L

  1. Disconnect TPS electrical connector.
  2. Remove TPS mounting screws.
  3. Remove TPS.

To Install:
The TPS is mounted to the throttle body. The throttle shaft end of throttle body slides into a socket in the TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.
  1. Install TPS and retaining screws.
  2. Tighten screws to 7 Nm (60 inch lbs.) torque.
  3. Connect TPS electrical connector to TPS.
  4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.

4.7L
  1. Remove air duct and air resonator box at throttle body.
  2. Disconnect TPS electrical connector.
  3. Remove two TPS mounting bolts (screws).
  4. Remove TPS from throttle body.

To Install:
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs. The TPS will be under slight tension when rotated.
  1. Install TPS and two retaining bolts.
  2. Tighten bolts to 7 Nm (60 inch lbs.) torque.
  3. Manually operate throttle control lever by hand to check for any binding of TPS.
  4. Connect TPS electrical connector to TPS.
  5. Install air duct/air box to throttle body.

Hope this helps

Dec 31, 2011 | 2001 Jeep Grand Cherokee

1 Answer

1990 lincoln continental throttle stuck wide open


make sure nothing is caught holding the plate open,disconnect the throttle cable from the throttle valve at the intake.if the throttle closes then i would say you have a problem with the cable itself and will need to be replaced.make sure there is nothing caught at the gas pedal that is holding open.if the throttle stays open then you may have a problem with the throttle shaft(dirt build up),bent shaft,damaged throttle plate,loose plate(has screws holding plate in position)on the shaft.it could also be a bad tps sensor(throttle position sensor)that is damaged internally and needs replacing,as it is fasten to the opposite of the throttle shaft from the cable.if you remove the screws(note position of sensor and screws on sensor)and remove the tps and the throttle is not stuck then this is probably the problem and needs replacing.

Jul 07, 2011 | Lincoln Continental Cars & Trucks

2 Answers

Do you have a picture to show where the throttle postion sensor should go?



Throttle Position Sensor Removal & Installation The throttle position sensor is an integral part of the Throttle Body and is only serviced as a complete unit.

Oct 14, 2010 | 2003 Cadillac CTS

1 Answer

How do I replace my throttle position sensor on a 2003 bonneville ssei


Hi, The tps is located on the side of the throttle body. Disconnect the wiring connector and then the two mounting screws. You may need to wiggle the tps a little to free it from the throttle body. Installing is just the reverse and there is no adjustment for these. Good Luck

Sep 13, 2010 | 2003 Pontiac Bonneville

2 Answers

Where is the TPS sensor and how hard is it to fix?


it should be on the throttle body (on the top of the engine)couple screws and about 20 minutes simple fix

Nov 21, 2009 | Jeep Cherokee Cars & Trucks

3 Answers

How to install a throttle position sensor on 93' 4.3 chevy 1500 truck


the two bolts that hold the sensor are torqued to 18 inch pounds. other than that it's self adjusted through the ecm

Apr 30, 2009 | Chevrolet 1500 Cars & Trucks

1 Answer

Need to know where the throttle body positon sensor is located?


The tps is usually on the side of the throttle body, some have a black plastic casing, just 2 screws hold on. Don't mistake it for the iac (idle air control) valve.

Jan 22, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14406 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...