Question about 2009 Hyundai Accent

Open Question

Blower fan only works on high speed 2009 accent

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jturcotte
  • 8140 Answers

SOURCE: blower fan for heater only

Check the resistor. If it looks heat damaged, replace or test with ohmmeter. Resistor is under dash at location indicated in picture below. You may have to remove part of the dash to see it. Also recommend you see my tip at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me.


jturcotte_52.gif

Posted on Nov 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2009 Nissan Quest I can't turn the heat off. Just stays on a high level of blowing out heat .


If you have a fan that has different speed settings (1234, or low med high etc) and the only one that works is high - then the blower resistor pack has failed. If you have a climate control unit (where you just pick a temp you want) then the fan is controlled by the heating system and it sets fan speed. If you have climate control style try lowering the temp to a lower setting (current temp in vehicle) and see if fan slows down. If not then climate control unit or fan resistor bad. If dial type and you get nothing on lower settings (only high works like mentioned above) you need to change blower resistor. It is located under dash near the fan itself. Look for small unit bolted in duct near fan with wire plug going to it.

Feb 23, 2015 | Nissan Cars & Trucks

1 Answer

Blower on 2009 Nissan sentra went from low to high by itself and won't turn down just stays on high ? What do I do


You may need a repair book to fix this. Looks like you have a control module and a fan control amplifier that controls fan speed. Both components are solid state meaning they don't use a mechanical relay. Either component could keep the fan speed on high.

Feb 20, 2014 | Cars & Trucks

1 Answer

2009 Nissan Quest My fan works on high all the


The resistor limits power to the blower to make for the slower speeds. It could be a sticking fan relay or the controller.

Aug 12, 2013 | 2002 Nissan Sentra

1 Answer

'05 Hyundai Accent. Just replaced the HVAC blower


HVAC = High Voltage.. I have no clue where that is on a Car. A Car operates on a 12Volt System and not on a 240Volt system

You have a Hot Wire crossed and going to the motor (Crossed Wires)
or
BAD MOTOR

Apr 10, 2013 | Cars & Trucks

2 Answers

Blower fan not working


The resistor bank is bad for slow speeds, the switch is bad for high speed. In your test, you have voltage, but the switch wont carry the amps, to run high speed. Open circuits will not blow fuses. Replace both switch and resistor bank for all speeds. Make sure to clean leaves and trash from fan housing and see if fan spins freely.

May 17, 2017 | Cars & Trucks

1 Answer

AC and Heater fan will only work on high speed, all fuses good. any ideas thanks, Dave


When the blower fan will only work on high speed setting this means the fans speed control resistor is burned out, when it fails the fan defaults to high speed only. The fan resistor is located next to the fan and held into the cooling air duct by 2 screws near the blower motor. The part is fairly cheap and easy to replace.

May 11, 2011 | 2000 Mercury Villager

2 Answers

01 grand.prix ac fan switch only works on high. has a duel temp controller when you turn fan off the only way fan comes back on is to move the temp controller levers


Hi!!
When the Blower Motor Resistor (controls blower speeds) goes bad, the blower motor works only on HIGH SPEED. REPLACE IT.
BLOWER MOTOR RESISTOR Removal & Installation
  • Disconnect negative battery cable.
  • Remove right lower instrument panel insulator panel.
  • Disconnect blower resistor connector located behind right side of dash.
  • Remove blower resistor screws and blower resistor.
To install, reverse removal procedure
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 18, 2011 | 2001 Pontiac Grand Prix

1 Answer

My ac/heater fan stopped blowing. There were no previous problems with the ac. How can I tell if it's just a blower fuse or the fan/motor itself. And where is the blower motor located?


Does it work on all speeds, or has it only stopped on #1 speed for instance....the blower motor is located at the passenger side footwell...

Sep 20, 2010 | 2003 Hyundai Accent

1 Answer

I have a 2004 Pacifica and the blower motor runs on high all the time, can't get it to work on slower speeds


The high blower works off a relay in the high speed only so the fan switch is at fault on your vehicle
Replace the fan blower control speed switch which is the one you adjust the lower fan speeds

Jun 15, 2010 | 2004 Chrysler Pacifica

Not finding what you are looking for?
2009 Hyundai Accent Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...