Question about 2006 Volkswagen Passat

Open Question

Replace shark fin antenna

How to pull back the hea the antennadliner to replace

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace ariel on a suzuki grand vitara 2004?


Its easy enough, first remove roof liner, then unbolt the shark fin radio antenna

Nov 17, 2016 | Suzuki Cars & Trucks

1 Answer

How to replace the antenna on 14 reg nissan qashqai with a shark fin


That is the Satellite antenna. How do you know it is the problem?

Jul 08, 2016 | Nissan Cars & Trucks

1 Answer

I have a square hole in my upper roof in the back section.what was there.i have a 2004taurus made by Ford


They make antennas called shark fins that are more seen in modern cars that would be my guess

Sep 11, 2015 | Ford Cars & Trucks

1 Answer

Factory stereo not working and needs replaced. how does dash come apart to do this


REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove cup holder.
  3. Remove trim panel above cupholder by pulling straight out.
  4. Remove center instrument panel trim panel.
  5. Remove screws holding radio to instrument panel.
  6. Pull radio rearward to gain access to the back of radio (RADIO). CAUTION: Pulling the antenna cable straight out of the radio without pulling on the locking antenna connector could damage the cable or radio.
  7. Disconnect the antenna cable by pulling the locking antenna connector away from the radio (ANTENNA TO RADIO).
  8. Disconnect bolt holding ground strap to the radio (if equipped).
  9. Disconnect the wire connectors from the back of the radio.

Nov 19, 2013 | 2002 Dodge Grand Caravan

1 Answer

Antenna


The only reason to have an electrical wire going to the antenna is for a motor that raises and lowers the antenna. The antenna cable to the radio is the only wire on the antenna.
To replace the antenna, you have to remove it from where it connects onto the car, then lift it out from there. The antenna and the cable cannot be separated, it's all one piece. You pull the cable off of the back of radio, and tie a strong string onto it, because when you lift out the antenna, the cable will be pulled out from under the dash and to wherever the antenna is situated and out that hole. Now tie the string onto (hope you had a long string, lol) the end of the cable on your new antenna and cable, and stick the end of the cable into the antenna mounting hole. Pull the string from under the dash by the radio and you will bring the cable back into the dash and where you can plug it into the old radio and listen to good old music again !

Feb 13, 2013 | Suzuki Alto Cars & Trucks

1 Answer

2002 Chrysler Town & Country antenna installation


Did the antenna break off in the mount or did the mount break.If antenna broke off in mount I would try drilling and tapping it.If you need a whole mount.Remove plug from back of radio attach good mechanics wire to it undo outer mount when you pull the wire out of the car the mechanics wire will follow afer you get it out put the mechanics wire on the new one tape over the wire to make it a smooth transition and pull mechanics wire inside the vehicle to reroute the antenna wire back to the radio.Be carefull you shouldnt have to pull super hard

Jun 04, 2012 | 2002 Chrysler Town & Country

1 Answer

Were is my hidden antena on 2001 acura 3.2tl


If your car does not have a little shark fin looking antenna on the roof, it is built into your windshield

Jul 17, 2011 | 2003 Acura 3.2TL

1 Answer

Where is the radio antenna on a 1997 328 is coupe


If you have a "shark fin" then it's the antenna, if not the rear screen heater is the antenna.

Oct 22, 2009 | 1997 BMW 328

1 Answer

How do you fit a shark fin ariel to a lexus is200


mounting a shark fin involves completely removing the headliner and drilling a hole in the roof.

Oct 19, 2009 | 2005 Lexus LS

1 Answer

Bulb failure pasrking light


Taillight bulb needs replacing, high above brake light at approx height of bottom of side widow.
Remove plastic panel at interior rear corner, remove thin backing insulation and reach up with fingers between metal flanges. Feel for a plastic "fin" approx 3" long x 1" wide that is attached to lightbulb. Similar "fin" for brake light is visible (white color). You need to feel above this. Fin is probably gray color, but you can't see it. Twist slightly counterclockwise and pull out. Bulb is attached to end of "fin". Insert new bulb and replace.

Nov 08, 2008 | 2002 Volvo V70

Not finding what you are looking for?
2006 Volkswagen Passat Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...