Question about 1995 Chevrolet Blazer

1 Answer

Replaced sensor per scan tool light still on 1995 blaer rt front

I replaced right front sensor per scan tool and the light is still on 1995 blazer

Posted by on

  • Richard Scordino May 11, 2010

    Do better than right front sensor...What is the sensor for? Did you clear codes from the computer when you finished?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Did you take the negative cable off to reset the codes?

Posted on May 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stalls while driving at 60 to 70 miles per hr. and while sitting still 2008 dodge ram quad pick up


Could be crankshaft position sensor ! after a crank sensor is replaced it needs to have a relearn done , Dealer or some other independent repair shop . Take it an have it checked out , unless you have a factory scan tool or a professional type scan tool .

Jan 06, 2016 | 2008 Dodge Ram Pickup 1500

1 Answer

I have a jeep comm 2007 50,000 ml i keep getting code po13c i change my sensors twice already.the code come back after 3 mounth when i drive 60 ml per hr.


old post, no engine size stated. 3.7, 4.7 or 5.7?
Fed or Cal car.?
the codes are real, but guessing the parts bad, dont work.
there are tests you can do , that will find any DTC.
the FSM lists them.
NO other DTC, using a full scan tool .?
if not using a scan tool, you may be blind to others.
the dash codes, are limited. USE a REAL SCAN TOOL.

P013C?
oxy 2/2 slow response. rich to lean.
Bank 2 sensor 2, is behind cat 2. right side. of car.
my guess is exhaust leak near here.
based on , front sensor 2/1 is happy.
any good shop with a smoke machine can find this is 15min flat.
why not get good help, that has good tools.???

here are the sensor rules, Cal versas FED:
The CAL car has mini cats and works differently.

If equipped with a California Emission Package, 4 sensors are used: 2 upstream (referred to as 1/1 and 2/1) and 2 downstream (referred to as 1/2 and 2/2). With this emission package, the right upstream sensor (2/1) is located in the right exhaust downpipe just before the mini-catalytic converter. The left upstream sensor (1/1) is located in the left exhaust downpipe just before the mini-catalytic converter. The right downstream sensor (2/2) is located in the right exhaust downpipe just after the mini-catalytic converter, and before the main catalytic converter. The left downstream sensor (1/2) is located in the left exhaust downpipe just after the mini-catalytic converter, and before the main catalytic converter.

Jan 31, 2014 | 2007 Jeep Commander 5.7

1 Answer

Traction active light comes on dash when sharp turning


Hello, this is normally caused by a wheel speed harness going to one of the front wheel speed sensors. this requires a high end scan tool that reads real time data to isolate which harness is at fault. or you could just replace both front harnes. cost is about 75.00 a harnesss. takes about 1 hour per side to replace

Jul 04, 2012 | 2005 Chevrolet Impala LS

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

1 Answer

I have a suzuki sidekick 1.6 and a replaced egr, sensor, intake conducts cleaned original replace crankshaft, pistons and rings even the pulley crank andwhen I drive al 45mls per hour suddenly the Service...


Engine light comes on, when there is code stored in the computer of the engine.You will need to get the computer scanned at local motorcycle/bike scan center.They do it by scan tool.But if no code is detected, then there is a reset procedure to reset engine light.The procedure to reset is simple.Just plug in scan tool or code reading into OBD2 DLC 16 pin connector above right knee. press reset DTC. The reset is done.If codes are in case detected, then codes will point towards faulty part, and you can replace the part as per the codes detected. --------------- This will help.Thanks.Helpmech,.

Apr 15, 2011 | Suzuki Sidekick Cars & Trucks

1 Answer

My ABS light stays on and the 4wd light keeps blinking.


The first thing you need to do is to have the abs computer scanned for codes, the abs may be related to the 4wd problem, by scanning the codes this will give you an idea of the problem, for example they scan it and it reads p1542 rt frt sensor out of spec, this would mean theres a problem with the right front speed sensor, when ever the computer sees a problem it stores a code and turns on the light for whatr ever system fails, hope this helps.

Oct 30, 2010 | 2006 Mazda Tribute

1 Answer

99 chevy blazer the abs light stays on all the time


There are several reasons why the abs light would come on. Mostly a bad tone ring or sensor within one of the front wheel bearings is bad. To truely know what the actual reason for the light you will need to have a local repair shop or your local auto parts store scan the abs system with a scan tool equipped with abs software. An easy way to rule out a bad wheel bearing , is to raise the front wheels and check for movement in the wheel up and down.

Aug 17, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

Abs light still on after replacing sensor per scan 1995 blazer


Remove negative battery cable for a couple of minutes to reset computer if you haven't already.

May 20, 2009 | 1995 Chevrolet Blazer

1 Answer

My service engine light is on. The computer code said catalis efficiency below threshold bank 1. Replaced the passenger side front o2 sensor and its still on. (did not know the truck has 4. Does anyone...


If the scan tool said bank one did it also say sensor one or two.If you replaced one and still is on then the second sensor is the problem..Just remember to undo the battery cables to reset the computer so car computer can reset its memory and turn the light of..

Mar 29, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...